Membuat File Sharing dengan Samba

Diskusi tentang Ubuntu Server baik webserver, database server, samba server dan service lainnya serta jaringan menggunakan Sistem Operasi Ubuntu.
Post Reply
User avatar
yuniar31

Membuat File Sharing dengan Samba

Post 09 Jun 2011, 15:09

Dear parA MasTer UbunTu, :D

Saya coba Samba untuk sharing data ke Window tapi masih belum bisa diakses, minta pencerahan untuk Samba .

Rencana saya ingin buat data sharing, yang masing2 datanya nanti bisa diakes di Window dengan 3 user berbeda yang dibuat di linux . mohon pencerahannya ...


:blush:


User avatar
yudiarbi
Contact:

Post 09 Jun 2011, 15:14

install dulu samba, mungkin bisa digabungin sama LDAP, di samba bisa bikin quota user kok, apalagi udah sama PDC, tambah mantap.... :D


User avatar
yuniar31

Post 09 Jun 2011, 15:33

udah saya instal mas, dan saya seting folder yang dishare.

saya coba dari windows, run pake IP tersebut engga bisa konek.

kenapa ya ?


User avatar
yudiarbi
Contact:

Post 09 Jun 2011, 15:47

udah dikonfigurasi di smb.conf?


User avatar
yuniar31

Post 09 Jun 2011, 15:54

saya konfigurasi lewat Webmin, sebelumnya saya coba untuk share bisa konek ke window, cuma mungkin ada kesalahan apa gt, saya coba add user lagi untuk membuat hak aksesnya . malah ga bisa konek ke IP Server dari window
.. :cry: :(


User avatar
sipelaut
Contact:

Post 09 Jun 2011, 19:16

pakek samba berapa broo
bisa dicopas kesini hasil sambanya
ketik "# tesparm"


User avatar
yuniar31

Post 09 Jun 2011, 21:07

ini saya copas bro :
root@server:/home/admin# tesparm
No command 'tesparm' found, did you mean:
Command 'testparm' from package 'samba-common-bin' (main)
Command 'testparm' from package 'samba4-common-bin' (universe)
tesparm: command not found

settingan yang mana ya bro yang salah, saya pake Webmin.


User avatar
sipelaut
Contact:

Post 09 Jun 2011, 21:34

31agustus wrote:ini saya copas bro :
root@server:/home/admin# tesparm
No command 'tesparm' found, did you mean:
Command 'testparm' from package 'samba-common-bin' (main)
Command 'testparm' from package 'samba4-common-bin' (universe)
tesparm: command not found

settingan yang mana ya bro yang salah, saya pake Webmin.

sori maksudnya testparm
sori-sori ngantuk


User avatar
yuniar31

Post 10 Jun 2011, 06:40

ini saya Copas lagi hasilnya :

root@server:/home/admin# testparm
Load smb config files from /etc/samba/smb.conf
rlimit_max: rlimit_max (1024) below minimum Windows limit (16384)
Processing section "[printers]"
Processing section "[print$]"
Processing section "[databank_samba_server]"
Loaded services file OK.
WARNING: You have some share names that are longer than 12 characters.
These may not be accessible to some older clients.
(Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.)
Server role: ROLE_STANDALONE
Press enter to see a dump of your service definitions

gimna bro ?


User avatar
sipelaut
Contact:

Post 10 Jun 2011, 08:49

31agustus wrote: Press enter to see a dump of your service definitions

gimna bro ?

tolong dienter lagi broo hasilnya lalu copas disini

lalu dibuat simple aja. jangan terlalu panjang
ada komentar ini soalnya

Code: Select all

Processing section "[databank_samba_server]"
Loaded services file OK.
WARNING: You have some share names that are longer than 12 characters.
These may not be accessible to some older clients.
(Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.)


User avatar
yuniar31

Post 10 Jun 2011, 09:05

Gini Bro, hasilnya :


[global]
workgroup = SAMBA
server string = Samba Server
security = SHARE
map to guest = Bad User
obey pam restrictions = Yes
pam password change = Yes
passwd program = /usr/bin/passwd %u
passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .
unix password sync = Yes
syslog = 0
log file = /var/log/samba/log.%m
max log size = 1000
dns proxy = No
usershare allow guests = Yes
panic action = /usr/share/samba/panic-action %d
read only = No

[printers]
comment = All Printers
path = /var/spool/samba
read only = Yes
create mask = 0700
printable = Yes
browseable = No

[print$]
comment = Printer Drivers
path = /var/lib/samba/printers
read only = Yes

[konsul_samba]
comment = Databankku
path = /media/serv1_data/bank_data


User avatar
yudiarbi
Contact:

Post 10 Jun 2011, 09:57

31agustus wrote:WARNING: You have some share names that are longer than 12 characters.
These may not be accessible to some older clients.
(Eg. Windows9x, WindowsMe, and smbclient prior to Samba 3.0.)
Server role: ROLE_STANDALONE
Press enter to see a dump of your service definitions
share names nya diganti bro, yang simple aj, oya workgroup sesuaikan dengan yang ad.....


User avatar
sipelaut
Contact:

Post 10 Jun 2011, 13:37

coba tambahkan parameter ini

Code: Select all

[konsul_samba]
comment = Databankku
path = /media/serv1_data/bank_data
guest ok = yes
writable = yes


User avatar
yuniar31

Post 10 Jun 2011, 13:56

untuk akses ke PC server sdh bisa Bro,ternyata maslahnya di Firewall PC server saya aktifin.skrg saya sdh Disable.

Untuk folder yang di share "[konsul_samba]" saya coba buka, Minta Password,mash belum bisa diakses saya coba masukin User & Password sambanya mash belum bisa masuk.

Kenapa ya ? saya pake Webmin, bisa kasih tw langkah2nya ?


User avatar
sipelaut
Contact:

Post 10 Jun 2011, 14:06

coba di chmod 0777 -R /direktori/yang/akan/di/share
cari tulisan
security = user. diubah jadi share
guest account = nobody

kalo ditempatku berhubung lan cardnya ada 3 jadi
untuk bagian interface saya arahin ke jaringan yang dituju

Code: Select all

interfaces = eth2 


User avatar
yuniar31

Post 10 Jun 2011, 14:18

sipelaut wrote:coba di chmod 0777 -R /direktori/yang/akan/di/share
cari tulisan
security = user. diubah jadi share
guest account = nobody

kalo ditempatku berhubung lan cardnya ada 3 jadi
untuk bagian interface saya arahin ke jaringan yang dituju

Code: Select all

interfaces = eth2 
itu di bagian menu mana ya webminnya ?
folder yang dishare bisa diakses, cuma untuk masuk folder tsb, itu minta user n paswwrd, saya sdh masukin user n password yang saya buat di linux, cuma engga bisa masuk ey ... :(


User avatar
sipelaut
Contact:

Post 10 Jun 2011, 14:20

wahhh aku gak pernah makek webmin
itu diketik diconsol broo
pakek user root
# chmod 0777 -R /direktori/yang/akan/di/share


User avatar
yuniar31

Post 10 Jun 2011, 14:33

ooOooo, gini bro hasilnya
[konsul_samba]
comment = Databanku
path = /media/serv1_data/bank_data
create mask = 0777
directory mask = 0777


User avatar
sipelaut
Contact:

Post 10 Jun 2011, 14:59

yuppp bisa juga seperti itu


User avatar
yuniar31

Post 10 Jun 2011, 15:28

bro, tapi belum bisa dibuka nih foldernya , minta password , saya coba isiin user & pasword yang dibuat di PC linux server tapi msh ga bisa masuk,

gmn ?


User avatar
sta

Post 10 Jun 2011, 15:41

yang dimasukin user samba apa bukan yah?


User avatar
yuniar31

Post 10 Jun 2011, 15:44

Iya, saya masukin User & pAsword yang saya Create di Server.


User avatar
sta

Post 10 Jun 2011, 15:49

coba copas smb.conf saat ini dan buat kan user n password samba baru untuk ngetes


User avatar
yuniar31

Post 10 Jun 2011, 16:52

kon gini bro ?

root@server:/home/admin# smb.conf
smb.conf: command not found


User avatar
dondonx

Post 10 Jun 2011, 17:13

harusnya masuk ke /etc/samba/smb.conf
lalu silahkan di edit dengan gedit ato pico om...


User avatar
yuniar31

Post 10 Jun 2011, 19:06

gini bro hasilnya :

root@server:/home/admin# /etc/samba/smb.conf
bash: /etc/samba/smb.conf: Permission denied


User avatar
yudiarbi
Contact:

Post 10 Jun 2011, 22:21

wah, mslh permission file, kok bisa root kok di denied?saya curiga salah konfigurasi tuh.//// :D


User avatar
yuniar31

Post 11 Jun 2011, 04:20

pencerahannya dunx bro ?


User avatar
yudiarbi
Contact:

Post 11 Jun 2011, 04:40

coba ceritain langkah2 yang bro lakukan dari awal termasuk smb.conf.nya..


User avatar
yuniar31

Post 11 Jun 2011, 07:47

add user > buat file yang ingin di share > atur directory yang dishare Lewat Webmin > sett. Samba Koneksi Window .. gt ,


User avatar
yudiarbi
Contact:

Post 11 Jun 2011, 08:05

konfigurasi smb.conf dikasih useraddscript untuk handle urusan user,buat direktori sebagai domain logon dan profile,buat user administrator jaringan, setup domain group, buat user linux dan user samba, terakhir buat user class....


User avatar
sipelaut
Contact:

Post 11 Jun 2011, 08:33

31agustus wrote: bro, tapi belum bisa dibuka nih foldernya , minta password , saya coba isiin user & pasword yang dibuat di PC Linux server tapi msh ga bisa masuk,
gmn ?
sudah chmod lom broo??

Code: Select all

# chmod 0777 -R /media/serv1_data/bank_data
31agustus wrote: gini bro hasilnya :

root@server:/home/admin# /etc/samba/smb.conf
bash: /etc/samba/smb.conf: Permission denied
yaa bakalan permissin denied
tambahin gedit atau nano broo didepan

Code: Select all

root@server:/home/admin# nano /etc/samba/smb.conf


User avatar
yuniar31

Post 11 Jun 2011, 10:07

scriptnya gmn ya ?


User avatar
Gung
Contact:

Post 15 Jun 2011, 04:40

wkkkwkwkkw saya ikut pusing jugak nih hadewhhhh.. eh kalu lgsg buka folder /etc/samba/ trus klik dua kali file smb.conf kan bisa ya?


User avatar
sipelaut
Contact:

Post 15 Jun 2011, 08:00

Gung wrote:wkkkwkwkkw saya ikut pusing jugak nih hadewhhhh.. eh kalu lgsg buka folder /etc/samba/ trus klik dua kali file smb.conf kan bisa ya?
blackshirt wrote:wew, kebiasaan windows :grin:

gagaggg.. sama
31agustus wrote:scriptnya gmn ya ?

sampek bingung mo jawab gimana???
script yang mana yahhh?? :)

dibantuin dong mastah hee..........


User avatar
yuniar31

Post 15 Jun 2011, 09:02

Untuk share udh bisa bro, maslahnya gini skrg ,

Directory file share di "media/folder_share" itu bisa share akses di window.

tapi kalo sya pake Directory file share di "media/partisi_drive/folder_share", itu tidak bisa diakses, gmna gan ?

Apa folder share hanya bisa di "media/folder_share" saja apa menggunakan "media/partisi_drive/folder_share" itu tidak bisa mengshare dari file pada drive berbeda.? untuk mengakses lewat window.?


User avatar
kermit

Post 07 Aug 2011, 19:48

master linux saya mau tanya donk.
saya sudah bisa untuk membuat sharing tetapi hanya bisa read doank tdk bisa write kira" kenapa ya masalahnya..
ini hasil smb.conf nya

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
# - When such options are commented with ";", the proposed setting
# differs from the default Samba behaviour
# - When commented with "#", the proposed setting is the default
# behaviour of Samba but the option is considered important
# enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic
# errors.
# A well-established practice is to name the original file
# "smb.conf.master" and create the "real" config file with
# testparm -s smb.conf.master >smb.conf
# This minimizes the size of the really used smb.conf file
# which, according to the Samba Team, impacts performance
# However, use this with caution if your smb.conf file contains nested
# "include" statements. See Debian bug #483187 for a case
# where using a master file is not a good idea.
#

#======================= Global Settings =======================

[global]
log file = /var/log/samba/log.%m
passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* %n\n
socket options = TCP_NODELAY
obey pam restrictions = yes
map to guest = bad user
encrypt passwords = yes
passwd program = /usr/bin/passwd %u
passdb backend = tdbsam
dns proxy = no
netbios name = toyofuji
writeable = yes
server string = %h server (Samba, Ubuntu)
unix password sync = yes
workgroup = tfsi
os level = 20
syslog = 0
security = user
usershare allow guests = yes
panic action = /usr/share/samba/panic-action %d
max log size = 1000
pam password change = yes

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of

# server string is the equivalent of the NT Description field

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
# wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.

# What naming service and in what order should we use to resolve host names
# to IP addresses
; name resolve order = lmhosts host wins bcast

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
; interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself. However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
; bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects

# Cap the size of the individual log files (in KiB).

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
# syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.

# Do something sensible when Samba crashes: mail the admin a backtrace


####### Authentication #######

# "security = user" is always a good idea. This will require a Unix account
# in this server for every user accessing the server. See
# /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/ServerType.html
# in the samba-doc package for details.
# security = user

# You may wish to use password encryption. See the section on
# 'encrypt passwords' in the smb.conf(5) manpage before enabling.

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.


# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan for
# sending the correct chat script for the passwd program in Debian Sarge).

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections

########## Domains ###########

# Is this machine able to authenticate users. Both PDC and BDC
# must have this setting enabled. If you are the BDC you must
# change the 'domain master' setting to no
#
; domain logons = yes
#
# The following setting only takes effect if 'domain logons' is set
# It specifies the location of the user's profile directory
# from the client point of view)
# The following required a [profiles] share to be setup on the
# samba server (see below)
; logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
# logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
; logon drive = H:
# logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
; logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe. The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the
# SAMR RPC pipe.
# The following assumes a "machines" group exists on the system
; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.
; add group script = /usr/sbin/addgroup --force-badname %g

########## Printing ##########

# If you want to automatically load your printer list rather
# than setting them up individually then you'll need this
# load printers = yes

# lpr(ng) printing. You may wish to override the location of the
# printcap file
; printing = bsd
; printcap name = /etc/printcap

# CUPS printing. See also the cupsaddsmb(8) manpage in the
# cupsys-client package.
; printing = cups
; printcap name = cups

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
; include = /home/samba/etc/smb.conf.%m

# Most people will find that this option gives better performance.
# See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html
# for details
# You may want to add the following on a Linux system:
# SO_RCVBUF=8192 SO_SNDBUF=8192
# socket options = TCP_NODELAY

# The following parameter is useful only if you have the linpopup package
# installed. The samba maintainer and the linpopup maintainer are
# working to ease installation and configuration of linpopup and samba.
; message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' &

# Domain Master specifies Samba to be the Domain Master Browser. If this
# machine will be configured as a BDC (a secondary logon server), you
# must set this to 'no'; otherwise, the default behavior is recommended.
# domain master = auto

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
; idmap uid = 10000-20000
; idmap gid = 10000-20000
; template shell = /bin/bash

# The following was the default behaviour in sarge,
# but samba upstream reverted the default because it might induce
# performance issues in large organizations.
# See Debian bug #368251 for some of the consequences of *not*
# having this setting and smb.conf(5) for details.
; winbind enum groups = yes
; winbind enum users = yes

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
; usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home directory as \\server\username
;[homes]
; comment = Home Directories
; browseable = yes

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
; read only = no

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
; create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
; directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server. Un-comment the following parameter
# to make sure that only "username" can connect to \\server\username
# This might need tweaking when using external authentication schemes
; valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
; comment = Network Logon Service
; path = /home/samba/netlogon
; guest ok = yes
; read only = no
; share modes = no

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
; comment = Users profiles
; path = /home/samba/profiles
; guest ok = yes
; browseable = yes
; create mask = 0600
; directory mask = 0700

[printers]
comment = All Printers
browseable = no
path = /var/spool/samba
printable = yes
guest ok = no
read only = yes
create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
comment = Printer Drivers
path = /var/lib/samba/printers
browseable = yes
read only = yes
guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
; write list = root, @lpadmin

# A sample share for sharing your CD-ROM with others.
;[cdrom]
; comment = Samba server's CD-ROM
; read only = yes
; locking = no
; path = /cdrom
; guest ok = yes

# The next two parameters show how to auto-mount a CD-ROM when the
# cdrom share is accesed. For this to work /etc/fstab must contain
# an entry like this:
#
# /dev/scd0 /cdrom iso9660 defaults,noauto,ro,user 0 0
#
# The CD-ROM gets unmounted automatically after the connection to the
#
# If you don't want to use auto-mounting/unmounting make sure the CD
# is mounted on /cdrom
#
; preexec = /bin/mount /cdrom
; postexec = /bin/umount /cdrom


[homes]
comment = Homes
writeable = yes





[kodok]
valid users = agus,leli
public = yes
path = /media/DATA
write list = agus,leli


User avatar
Rezaazz079

Post 29 Apr 2013, 11:02

tapi udah ada file nya cuma ga bisa di akses di pc laen knp tuh gan???? pencerahannya yaaah....


User avatar
maseadi

Post 03 Jun 2013, 08:50

Ada yang mau jelasin Quota untuk samba ndak ya? aku dah nyoba nstal kok ngak berhasil..


User avatar
q_p
Contact:

Post 03 Jun 2013, 16:49

Bagaimana anda meng-install-nya ? dengan apt-get atau compile.
  • Secara default jika dilakukan apt-get, fitur ini dalam mode off. Agar support dengan disk-quota anda mesti compile dengan mamsukkan opsi '--with-quotas'.
  • Edit fstab, tambahkan option-mounting yaitu usrquota dan grpquota pada partisi yang anda share.
  • Konfigur quota masing2 user-group samba
Usefull link =
http://linuxgazette.net/149/prestia.html


User avatar
maseadi

Post 11 Jun 2013, 19:07

Aku instal pakai apt-get...

belum paham alurnya quotas dengan sambanya?


User avatar
q_p
Contact:

Post 12 Jun 2013, 00:49

maseadi wrote:Aku instal pakai apt-get...

belum paham alurnya quotas dengan sambanya?
Jadi anda mesti melakukan compile agar bisa menggunakan fitur disk-quota


User avatar
myitanium

Post 12 Jun 2013, 09:30

Klo saya, biasanya ini yang saya lakukan untuk SMB server+kuota
1. Install samba (jangan lupa folder home di share ya)
2. Install webmin (helpfull banget untuk menyederhanakan semua kerumitan terminal+kuota)

Klo tambah user SMB+kuota:
1. Tambah dari webmin untuk Linux usernya
2. Tambah user SMB, masuk terminal ketik: smbpasswd -a usernamenya_apa
3. Atur kuota per username dari webmin


User avatar
q_p
Contact:

Post 12 Jun 2013, 17:43

myitanium wrote:Klo saya, biasanya ini yang saya lakukan untuk SMB server+kuota
1. Install samba (jangan lupa folder home di share ya)
2. Install webmin (helpfull banget untuk menyederhanakan semua kerumitan terminal+kuota)

Klo tambah user SMB+kuota:
1. Tambah dari webmin untuk Linux usernya
2. Tambah user SMB, masuk terminal ketik: smbpasswd -a usernamenya_apa
3. Atur kuota per username dari webmin
Bisa ya dengan webmin ?
Misalnya selesai dikonfigurasi quota jika webmin di-uninstall, apakah konfigurasi-quota tsb hilang atau masih ?


User avatar
myitanium

Post 14 Jun 2013, 12:30

@pragola_pati: setahu saya pengaturan tidak hilang. Webmin hanya web interface untuk membantu pengaturan sistem.
Anda bisa pakai webmin untuk macam2. Bukan hanya kuota.


User avatar
sipelaut
Contact:

Post 14 Jun 2013, 13:57

ane kapok dah main2 ama webmin
gara2 utility ini file ane yang udah diedit gak tau kesimpen dimana :hajarpc:

gara2 itu juga DNS ane sampek eror.. hakakk..., munkin mode next2 gak cocok kali ya buat ane........ :hajarpc:


User avatar
abu_unaisah

Post 14 Jun 2013, 14:08

kalo mo maen2 sama barang baru di backup dulu om
sing sabar


User avatar
q_p
Contact:

Post 14 Jun 2013, 17:23

@myitanium
Lha ini yang saya kuatirkan =
sipelaut wrote:...
gara2 utility ini file ane yang udah diedit gak tau kesimpen dimana
...


Post Reply

Who is online

Users browsing this forum: No registered users and 111 guests