[help]setting modem flexi

Membahas Perangkat-perangkat keras yang belum dideteksi dengan baik oleh Ubuntu serta solusinya.
Post Reply
User avatar
dhit

[help]setting modem flexi

Post 28 Aug 2011, 12:23

rekan2 forum,sya btuh pertolongan....
sya baru pke ubuntu 10.10, modem sya air flash flexi g bsa di gunain ..
smua cara yg sya bca sya coba,tp ttp g bsa konek..
tolong ya di bantu, cz sya pgn ganti os dari win xp ke linux ..
tp sma jg bhong klo g bsa buat OL ...
t x z


User avatar
yudiarbi
Contact:

Post 28 Aug 2011, 13:11

ni modemnya juga usb storage kan?jalanin modprobe dulu bos, biar di switch modemnya, search, ada di forum kok, habis modprobe, wvdial di configurasi sesuai modem, baru di dial pake wvdial


User avatar
dhit

Post 28 Aug 2011, 15:08

udah boz,udh sya modprobe,tp ttp g bsa konek ...
sya coba sudo dmesg | grep CD-ROM, modem terdetek EVDO USB-STORAGE..
emang guna nya modprobe utk ap ya ..
maklum newbie,jd g tau ..


User avatar
thrvers
Contact:

Post 28 Aug 2011, 15:17

'
abis colok modem, terus:
$ sudo dmesg | grep CD-ROM

isinya copas sini :D


User avatar
dhit

Post 28 Aug 2011, 16:22

umbara@umbara-HP-d220-MT-PK464PA:~$ lsusb
Bus 004 Device 003: ID 1c9e:6000
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 1e4e:0100
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

umbara@umbara-HP-d220-MT-PK464PA:~$ sudo dmesg | grep CD-ROM
[ 0.922169] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-H552U US03 PQ: 0 ANSI: 5
[ 0.927231] Uniform CD-ROM driver Revision: 3.20
[ 0.927501] sr 1:0:0:0: Attached scsi CD-ROM sr0

umbara@umbara-HP-d220-MT-PK464PA:~$ sudo wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

ttyS0: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan: S1 S2 S3
WvModem: Cannot get information for serial port.
ttyUSB0: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB0: ATQ0 V1 E1 -- and failed too at 115200, giving up.


Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial

If you still have problems, send mail to .


User avatar
dhit

Post 28 Aug 2011, 16:23

semoga rekan2 bersedia membantu,biar permaslahan sya cpt selesai...
coz sya pgn cpt2 gnti OS, udh jenuh pke win xp,..
gmpang kena virus ...
txzzzz


User avatar
yudiarbi
Contact:

Post 28 Aug 2011, 19:12

di modprobe gunanya biar modem yg mode storage berubah menjadi mode modem, stlh itu coba hasil dmesg bro, cari yg bagian /dev/ttyUsbx -> x bisa 0,1,2,3 dstnya, kl udah ketemu di wvdial.conf definisikan alamat modemnya(/dev/ttyUSb itu) baru di wvdial, kl udah bisa masukin modprobenya di /etc/rc.local


User avatar
thrvers
Contact:

Post 29 Aug 2011, 03:13

'
$ lsusb
sepertinya yg ini: Bus 001 Device 003: ID 1e4e:0100

$ sudo dmesg | grep CD-ROM
sepertinya dikenali sbg storage [sr1 sebab ada DVDROM di sr0]

selanjutnya coba:
$ eject /dev/sr1

kemudian lihat output lsusb lagi spt apa??


User avatar
dhit

Post 30 Aug 2011, 13:25

maaf mas, bukan nya modem nya itu yg 1c9e:6000,
coz swaktu sya colokin modem nya,perbedaan nya disitu,..
ap mgkn sya slah..

sewaktu sya ketik eject di terminal, ada bacaan gni mas ..
eject: unable to find or open device for: '/dev/sr1'.

sy coba pinjem modem tmen,
trs sya pke cara mas, udh berhasil,..
tp di modem sya ga..
tlong bantuan nya mas, msa sya harus pinjem modem tmen trs ...

txz


User avatar
dhit

Post 31 Aug 2011, 09:58

rekan, tolongn sya, udh dari hari minggu mslah modem sya blm teratasi ...


User avatar
thrvers
Contact:

Post 31 Aug 2011, 18:12

'
dhit wrote:maaf mas, bukan nya modem nya itu yg 1c9e:6000,
coz swaktu sya colokin modem nya,perbedaan nya disitu,..
ap mgkn sya slah..
....

mungkin saja benar kak dhit :D modemnya yg 1c9e:6000
kalau sudah terdeteksi spt itu, tinggal ketik:

Code: Select all

$ sudo modprobe usbserial vendor=0x1c9e product=6000
terus coba cek di nm-applet ato wvdial-nya

CMIIW


User avatar
dhit

Post 31 Aug 2011, 23:09

udh sya lakukan kya gto, tp ttp aj g bsa, sy coba pke modem temen bisa, tp modem sya gak ..
pke modem tmen, sya gunain perintah eject sr1, trs sudo modprobe ..
klo nm-applet itu ap..
txz , smoga berkenan membantu permasalahan sya yg blm selesai ini ..


User avatar
dhit

Post 03 Sep 2011, 00:51

blm slsai jg prmslhan sya .


User avatar
dhit

Post 03 Sep 2011, 09:55

tlong bantu sya, modem sy msh blm bsa di gunakan,

umbara@umbara-HP-d220-MT-PK464PA:~$ lsusb
Bus 004 Device 003: ID 1c9e:6000
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 1e4e:0100
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

diatas, modem terdeteksi Bus 004 Device 003: ID 1c9e:6000,
tp setelah sya ketikan perintah sudo modprobe,
modem hilang, tdk terdeteksi, knpa ya,..
.

umbara@umbara-HP-d220-MT-PK464PA:~$ lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 1e4e:0100
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

tlong bantu sya, sya bner2 baru menggunakan linux, dan ingin menggunakan nya, tp g ad yg bantu sya ..
txz, maaf jka ad slah2 kta
(minal aidzin walfaidzin,mohon maaf lahir batin)


User avatar
yudiarbi
Contact:

Post 03 Sep 2011, 10:39

setelah di modprobe, lgsg dmesg,cari yg /dev/ttyUSBxx, bisa 0,1,2 dstnya, nah itulah device modemnya
variabel /dev/ttyUSBxx itu ditulis di wvdial.conf untuk dialnya


User avatar
dhit

Post 05 Sep 2011, 00:34

maaf ya mas yudi, bkan'y klo modem kedeteck tgl di cari di
system>network connections>mobile broadband>add..
ntar di "create a connection for this mobile broad band device" di situ kebaca modem nya, soal nya kemarin lusa sya pke modem tmen, pke cara itu ...
apa harus pke wvdial ...
mang fungsi wvdial itu untuk apa,???
txz,(maaf bnyak brtanya)..


User avatar
dhit

Post 05 Sep 2011, 00:50

maaf mas, ini hasil dri perintah dmesg,
sya g tau mna yg kedeteksi sebagai modem nya ..

mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2499.722 MHz processor.
[ 0.008007] Calibrating delay loop (skipped), value calculated using timer frequency.. 4999.44 BogoMIPS (lpj=9998888)
[ 0.008108] pid_max: default: 32768 minimum: 301
[ 0.008181] Security Framework initialized
[ 0.008255] AppArmor: AppArmor initialized
[ 0.008304] Yama: becoming mindful.
[ 0.008431] Mount-cache hash table entries: 512
[ 0.008691] Initializing cgroup subsys ns
[ 0.008743] Initializing cgroup subsys cpuacct
[ 0.008797] Initializing cgroup subsys memory
[ 0.008857] Initializing cgroup subsys devices
[ 0.008907] Initializing cgroup subsys freezer
[ 0.008957] Initializing cgroup subsys net_cls
[ 0.009046] CPU0: Hyper-Threading is disabled
[ 0.009098] mce: CPU supports 4 MCE banks
[ 0.009157] CPU0: Thermal monitoring enabled (TM1)
[ 0.009221] Performance Events: Netburst events, Netburst P4/Xeon PMU driver.
[ 0.009366] ... version: 0
[ 0.009414] ... bit width: 40
[ 0.009462] ... generic registers: 18
[ 0.009510] ... value mask: 000000ffffffffff
[ 0.009560] ... max period: 0000007fffffffff
[ 0.009609] ... fixed-purpose events: 0
[ 0.009658] ... event mask: 000000000003ffff
[ 0.012760] SMP alternatives: switching to UP code
[ 0.025861] ACPI: Core revision 20100428
[ 0.032987] ftrace: converting mcount calls to 0f 1f 44 00 00
[ 0.033045] ftrace: allocating 21758 entries in 43 pages
[ 0.036140] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.036515] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.078832] CPU0: Intel(R) Pentium(R) 4 CPU 2.50GHz stepping 09
[ 0.080000] Brought up 1 CPUs
[ 0.080000] Total of 1 processors activated (4999.44 BogoMIPS).
[ 0.080000] devtmpfs: initialized
[ 0.080000] regulator: core version 0.5
[ 0.080000] Time: 0:34:56 Date: 09/05/11
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] EISA bus registered
[ 0.080024] ACPI: bus type pci registered
[ 0.082114] PCI: PCI BIOS revision 2.10 entry at 0xfdb61, last bus=3
[ 0.082165] PCI: Using configuration type 1 for base access
[ 0.083569] bio: create slab at 0
[ 0.084865] ACPI: EC: Look up EC in DSDT
[ 0.090734] ACPI: Interpreter enabled
[ 0.090789] ACPI: (supports S0 S3 S4 S5)
[ 0.090990] ACPI: Using IOAPIC for interrupt routing
[ 0.097041] ACPI: Power Resource [URP1] (off)
[ 0.097135] ACPI: Power Resource [URP2] (off)
[ 0.097221] ACPI: Power Resource [FDDP] (off)
[ 0.097307] ACPI: Power Resource [LPTP] (off)
[ 0.097523] ACPI: No dock devices found.
[ 0.097574] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.097822] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.098157] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.098161] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.098165] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.098169] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.098172] pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xffdfffff] (ignored)
[ 0.098176] pci_root PNP0A03:00: host bridge window [mem 0xfee01000-0xffdfffff] (ignored)
[ 0.098209] pci 0000:00:00.0: reg 10: [mem 0xe0000000-0xe7ffffff pref]
[ 0.098299] pci 0000:00:02.0: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[ 0.098307] pci 0000:00:02.0: reg 14: [mem 0xdff80000-0xdfffffff]
[ 0.098433] pci 0000:00:1d.0: reg 20: [io 0xe400-0xe41f]
[ 0.098496] pci 0000:00:1d.1: reg 20: [io 0xe800-0xe81f]
[ 0.098558] pci 0000:00:1d.2: reg 20: [io 0xec00-0xec1f]
[ 0.098622] pci 0000:00:1d.7: reg 10: [mem 0xdff7bc00-0xdff7bfff]
[ 0.098687] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.098693] pci 0000:00:1d.7: PME# disabled
[ 0.098752] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.098754] * this clock source is slow. If you are sure your timer does not have
[ 0.098756] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.098967] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by ICH4 ACPI/GPIO/TCO
[ 0.099029] pci 0000:00:1f.0: quirk: [io 0x0400-0x043f] claimed by ICH4 GPIO
[ 0.099106] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.099114] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.099122] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.099130] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.099138] pci 0000:00:1f.1: reg 20: [io 0xfc00-0xfc0f]
[ 0.099147] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff]
[ 0.099206] pci 0000:00:1f.3: reg 20: [io 0x0c00-0x0c1f]
[ 0.099259] pci 0000:00:1f.5: reg 10: [io 0xe000-0xe0ff]
[ 0.099267] pci 0000:00:1f.5: reg 14: [io 0xdc00-0xdc3f]
[ 0.099275] pci 0000:00:1f.5: reg 18: [mem 0xdff7ba00-0xdff7bbff]
[ 0.099283] pci 0000:00:1f.5: reg 1c: [mem 0xdff7b900-0xdff7b9ff]
[ 0.099318] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
[ 0.099324] pci 0000:00:1f.5: PME# disabled
[ 0.099386] pci 0000:03:0a.0: reg 10: [mem 0xdfdfe000-0xdfdfffff]
[ 0.099417] pci 0000:03:0a.0: reg 30: [mem 0xdfdc0000-0xdfddffff pref]
[ 0.099438] pci 0000:03:0a.0: supports D1 D2
[ 0.099440] pci 0000:03:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.099445] pci 0000:03:0a.0: PME# disabled
[ 0.099481] pci 0000:00:1e.0: PCI bridge to [bus 03-03] (subtractive decode)
[ 0.099536] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.099542] pci 0000:00:1e.0: bridge window [mem 0xdfd00000-0xdfdfffff]
[ 0.099548] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.099551] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
[ 0.099555] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
[ 0.099566] pci_bus 0000:00: on NUMA node 0
[ 0.099572] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.099726] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT]
[ 0.116532] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.117095] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.117655] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.118280] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.118840] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.119473] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.120117] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.120815] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.121302] HEST: Table is not found!
[ 0.121472] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.121539] vgaarb: loaded
[ 0.121862] SCSI subsystem initialized
[ 0.122022] libata version 3.00 loaded.
[ 0.122107] usbcore: registered new interface driver usbfs
[ 0.122174] usbcore: registered new interface driver hub
[ 0.122258] usbcore: registered new device driver usb
[ 0.122515] ACPI: WMI: Mapper loaded
[ 0.122564] PCI: Using ACPI for IRQ routing
[ 0.122690] PCI: pci_cache_line_size set to 64 bytes
[ 0.122753] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.122757] reserve RAM buffer: 000000001f7f0000 - 000000001fffffff
[ 0.122915] NetLabel: Initializing
[ 0.122963] NetLabel: domain hash size = 128
[ 0.123010] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.123075] NetLabel: unlabeled traffic allowed by default
[ 0.123191] Switching to clocksource tsc
[ 0.136795] AppArmor: AppArmor Filesystem Enabled
[ 0.136893] pnp: PnP ACPI init
[ 0.136987] ACPI: bus type pnp registered
[ 0.140534] pnp: PnP ACPI: found 11 devices
[ 0.140584] ACPI: ACPI bus type pnp unregistered
[ 0.140636] PnPBIOS: Disabled by ACPI PNP
[ 0.140700] system 00:01: [io 0x03f0-0x03f1] has been reserved
[ 0.140772] system 00:01: [io 0x04d0-0x04d1] has been reserved
[ 0.140822] system 00:01: [io 0x0400-0x043f] has been reserved
[ 0.140873] system 00:01: [io 0x0a00-0x0a7f] has been reserved
[ 0.140925] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.177840] pci 0000:00:1f.1: BAR 5: assigned [mem 0x20000000-0x200003ff]
[ 0.177900] pci 0000:00:1f.1: BAR 5: set to [mem 0x20000000-0x200003ff] (PCI address [0x20000000-0x200003ff]
[ 0.177965] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[ 0.178014] pci 0000:00:1e.0: bridge window [io disabled]
[ 0.178067] pci 0000:00:1e.0: bridge window [mem 0xdfd00000-0xdfdfffff]
[ 0.178120] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.178188] pci 0000:00:1e.0: setting latency timer to 64
[ 0.178195] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.178198] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.178202] pci_bus 0000:03: resource 1 [mem 0xdfd00000-0xdfdfffff]
[ 0.178205] pci_bus 0000:03: resource 4 [io 0x0000-0xffff]
[ 0.178209] pci_bus 0000:03: resource 5 [mem 0x00000000-0xffffffff]
[ 0.178275] NET: Registered protocol family 2
[ 0.178412] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.178743] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.178940] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.179125] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.179176] TCP reno registered
[ 0.179224] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.179283] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.179449] NET: Registered protocol family 1
[ 0.179522] pci 0000:00:02.0: Boot video device
[ 0.179640] PCI: CLS 0 bytes, default 64
[ 0.179947] cpufreq-nforce2: No nForce2 chipset.
[ 0.180041] Scanning for low memory corruption every 60 seconds
[ 0.180259] audit: initializing netlink socket (disabled)
[ 0.180325] type=2000 audit(1315182895.176:1): initialized
[ 0.190543] Trying to unpack rootfs image as initramfs...
[ 0.204963] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.213137] VFS: Disk quotas dquot_6.5.2
[ 0.213338] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.214423] fuse init (API version 7.14)
[ 0.214617] msgmni has been set to 944
[ 0.221145] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.221214] io scheduler noop registered
[ 0.221262] io scheduler deadline registered
[ 0.221326] io scheduler cfq registered (default)
[ 0.221557] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.221638] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.221963] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.222032] ACPI: Power Button [PWRB]
[ 0.222151] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.222213] ACPI: Power Button [PWRF]
[ 0.222455] ACPI: acpi_idle registered with cpuidle
[ 0.225222] ERST: Table is not found!
[ 0.225557] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.225727] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.226268] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.227989] brd: module loaded
[ 0.233275] isapnp: Scanning for PnP cards...
[ 0.238940] loop: module loaded
[ 0.239384] ata_piix 0000:00:1f.1: version 2.13
[ 0.239412] alloc irq_desc for 18 on node -1
[ 0.239415] alloc kstat_irqs on node -1
[ 0.239430] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.239565] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.245032] scsi0 : ata_piix
[ 0.288907] scsi1 : ata_piix
[ 0.291458] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
[ 0.291512] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
[ 0.292166] Fixed MDIO Bus: probed
[ 0.292268] PPP generic driver version 2.4.2
[ 0.292443] tun: Universal TUN/TAP device driver, 1.6
[ 0.292492] tun: (C) 1999-2004 Max Krasnyansky
[ 0.292679] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.292791] alloc irq_desc for 23 on node -1
[ 0.292794] alloc kstat_irqs on node -1
[ 0.292806] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 0.292884] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.292890] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.292986] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.293093] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.297029] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 0.301315] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xdff7bc00
[ 0.325153] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.325502] hub 1-0:1.0: USB hub found
[ 0.325555] hub 1-0:1.0: 6 ports detected
[ 0.325707] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.325780] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.325915] alloc irq_desc for 16 on node -1
[ 0.325919] alloc kstat_irqs on node -1
[ 0.325932] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.325995] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.326001] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.326118] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.326223] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e400
[ 0.326447] hub 2-0:1.0: USB hub found
[ 0.326500] hub 2-0:1.0: 2 ports detected
[ 0.326619] alloc irq_desc for 19 on node -1
[ 0.326622] alloc kstat_irqs on node -1
[ 0.326628] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.326686] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.326691] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.326790] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.326882] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800
[ 0.327101] hub 3-0:1.0: USB hub found
[ 0.327152] hub 3-0:1.0: 2 ports detected
[ 0.327265] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.327323] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.327327] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.327422] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.327515] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ec00
[ 0.327751] hub 4-0:1.0: USB hub found
[ 0.327803] hub 4-0:1.0: 2 ports detected
[ 0.328001] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 0.328052] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.328937] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.333416] mice: PS/2 mouse device common for all mice
[ 0.333694] rtc_cmos 00:04: RTC can wake from S4
[ 0.333815] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.333899] rtc0: alarms up to one month, y3k, 114 bytes nvram
[ 0.334154] device-mapper: uevent: version 1.0.3
[ 0.334404] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[ 0.340482] device-mapper: multipath: version 1.1.1 loaded
[ 0.340544] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.340946] EISA: Probing bus 0 at eisa.0
[ 0.341034] EISA: Detected 0 cards.
[ 0.345306] cpuidle: using governor ladder
[ 0.345363] cpuidle: using governor menu
[ 0.345869] TCP cubic registered
[ 0.346125] NET: Registered protocol family 10
[ 0.346683] lo: Disabled Privacy Extensions
[ 0.347015] NET: Registered protocol family 17
[ 0.347163] Using IPI No-Shortcut mode
[ 0.347377] PM: Resume from disk failed.
[ 0.347395] registered taskstats version 1
[ 0.347642] Magic number: 11:418:556
[ 0.347751] pci_link PNP0C0F:07: hash matches
[ 0.347849] rtc_cmos 00:04: setting system clock to 2011-09-05 00:34:56 UTC (1315182896)
[ 0.347913] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.347962] EDD information not available.
[ 0.402056] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 0.493770] ata2.00: ATAPI: TSSTcorpCD/DVDW TS-H552U, US03, max UDMA/33
[ 0.501550] ata1.00: HPA unlocked: 78163247 -> 78165360, native 78165360
[ 0.501613] ata1.00: ATA-6: ST340014A, 3.54, max UDMA/100
[ 0.501663] ata1.00: 78165360 sectors, multi 16: LBA48
[ 0.502057] ata2.00: configured for UDMA/33
[ 0.517631] ata1.00: configured for UDMA/100
[ 0.664609] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 0.924616] isapnp: No Plug & Play device found
[ 0.924944] scsi 0:0:0:0: Direct-Access ATA ST340014A 3.54 PQ: 0 ANSI: 5
[ 0.925312] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.925623] sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
[ 0.925887] sd 0:0:0:0: [sda] Write Protect is off
[ 0.925940] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.925988] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-H552U US03 PQ: 0 ANSI: 5
[ 0.926346] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.926741] sda:sr0: scsi3-mmc drive: 15x/48x writer cd/rw xa/form2 cdda tray
[ 0.929681] Uniform CD-ROM driver Revision: 3.20
[ 0.929948] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 0.930067] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 0.943600] sda1 sda2 sda3
[ 0.980794] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.189462] Freeing initrd memory: 16144k freed
[ 1.223637] Freeing unused kernel memory: 684k freed
[ 1.225132] Write protecting the kernel text: 4932k
[ 1.225220] Write protecting the kernel read-only data: 1976k
[ 1.263438] ramzswap: disk size not provided. You can use disksize_kb module param to specify size.
[ 1.263442] Using default: (25% of RAM).
[ 1.263556] ramzswap: disk size set to 125076 kB
[ 1.284307] udev[75]: starting version 163
[ 1.396128] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 1.642748] Floppy drive(s): fd0 is 1.44M
[ 1.644305] Linux agpgart interface v0.103
[ 1.663313] FDC 0 is a post-1991 82077
[ 1.684464] agpgart-intel 0000:00:00.0: Intel 830M Chipset
[ 1.684889] agpgart-intel 0000:00:00.0: detected 8060K stolen memory
[ 1.700806] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd0000000
[ 1.715235] b44 0000:03:0a.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 1.749643] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x04, vendor 0x4243)
[ 1.749654] ssb: Core 1 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
[ 1.749661] ssb: Core 2 found: PCI (cc 0x804, rev 0x02, vendor 0x4243)
[ 1.752760] usbcore: registered new interface driver hiddev
[ 1.753829] [drm] Initialized drm 1.1.0 20060810
[ 1.767261] input: Logitech Optical USB Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input3
[ 1.767993] generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1/input0
[ 1.771955] usbcore: registered new interface driver usbhid
[ 1.772042] usbhid: USB HID core driver
[ 1.788305] ssb: Sonics Silicon Backplane found on PCI device 0000:03:0a.0
[ 1.788394] b44: b44.c:v2.0
[ 1.807319] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.807385] i915 0000:00:02.0: setting latency timer to 64
[ 1.812277] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:02:e3:55:9a:e5
[ 1.830248] [drm] set up 15M of stolen space
[ 1.854549] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.855016] [drm] initialized overlay support
[ 2.083433] Console: switching to colour frame buffer device 160x64
[ 2.091032] fb0: inteldrmfb frame buffer device
[ 2.091081] drm: registered panic notifier
[ 2.091625] Slow work thread pool: Starting up
[ 2.091780] Slow work thread pool: Ready
[ 2.091845] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 5.841927] Btrfs loaded
[ 5.851535] xor: automatically using best checksumming function: pIII_sse
[ 5.868009] pIII_sse : 3185.000 MB/sec
[ 5.868051] xor: using function: pIII_sse (3185.000 MB/sec)
[ 5.873883] device-mapper: dm-raid45: initialized v0.2594b
[ 45.190372] end_request: I/O error, dev fd0, sector 0
[ 45.468714] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 59.251913] Adding 506876k swap on /dev/sda6. Priority:-1 extents:1 across:506876k
[ 59.405798] udev[365]: starting version 163
[ 59.761971] intel_rng: FWH not detected
[ 59.775744] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 60.104372] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
[ 60.154197] lp: driver loaded but no devices found
[ 60.228291] parport_pc 00:0a: reported by Plug and Play ACPI
[ 60.228349] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 60.262165] Linux video capture interface: v2.00
[ 60.320385] lp0: using parport0 (interrupt-driven).
[ 60.355451] uvcvideo: Found UVC 1.00 device USB2.0 Camera (1e4e:0100)
[ 60.387723] uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround.
[ 60.393343] input: USB2.0 Camera as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1:1.0/input/input4
[ 60.393443] usbcore: registered new interface driver uvcvideo
[ 60.393448] USB Video Class driver (v0.1.0)
[ 60.493763] ppdev: user-space parallel port driver
[ 60.976669] type=1400 audit(1315157757.126:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=618 comm="apparmor_parser"
[ 60.977362] type=1400 audit(1315157757.126:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=618 comm="apparmor_parser"
[ 60.977749] type=1400 audit(1315157757.126:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=618 comm="apparmor_parser"
[ 61.457481] alloc irq_desc for 17 on node -1
[ 61.457487] alloc kstat_irqs on node -1
[ 61.457500] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 61.457559] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 61.876034] intel8x0_measure_ac97_clock: measured 52338 usecs (2522 samples)
[ 61.876040] intel8x0: clocking to 48000
[ 62.866011] type=1400 audit(1315157759.014:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=913 comm="apparmor_parser"
[ 62.876115] type=1400 audit(1315157759.026:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=919 comm="apparmor_parser"
[ 62.877627] type=1400 audit(1315157759.026:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=919 comm="apparmor_parser"
[ 62.878026] type=1400 audit(1315157759.026:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=919 comm="apparmor_parser"
[ 63.215970] type=1400 audit(1315157759.362:9): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=924 comm="apparmor_parser"
[ 63.225738] type=1400 audit(1315157759.374:10): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=924 comm="apparmor_parser"
[ 63.232323] type=1400 audit(1315157759.382:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=924 comm="apparmor_parser"
[ 64.395912] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 73.824347] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0
[ 91.023261] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 91.097081] ISOFS: changing to secondary root
[ 132.719733] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 132.719743] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance
[ 132.719746] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[ 132.719747] vboxdrv: the usage of hardware performance counters by
[ 132.719749] vboxdrv: echo 2 > /proc/sys/kernel/perf_counter_paranoid
[ 132.719755] vboxdrv: Found 1 processor cores.
[ 132.725043] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 132.725049] vboxdrv: Successfully loaded version 3.2.10 (interface 0x00140001).
[ 766.528023] usb 4-2: new full speed USB device using uhci_hcd and address 2
[ 766.816652] Initializing USB Mass Storage driver...
[ 766.816862] scsi2 : usb-storage 4-2:1.0
[ 766.817183] usbcore: registered new interface driver usb-storage
[ 766.817188] USB Mass Storage support registered.
[ 767.829011] scsi 2:0:0:0: CD-ROM EVDO MMC Storage 2.31 PQ: 0 ANSI: 2
[ 767.853987] sr1: scsi-1 drive
[ 767.854243] sr 2:0:0:0: Attached scsi CD-ROM sr1
[ 767.854383] sr 2:0:0:0: Attached scsi generic sg2 type 5
[ 769.897890] sr1: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00
[ 769.897911] sr: Sense Key : Hardware Error [current]
[ 769.897918] sr: Add. Sense: No additional sense information
[ 770.012120] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.168030] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.288026] usb 4-2: device descriptor read/64, error -71
[ 801.512040] usb 4-2: device descriptor read/64, error -71
[ 801.728054] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.848037] usb 4-2: device descriptor read/64, error -71
[ 802.072047] usb 4-2: device descriptor read/64, error -71
[ 802.288052] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 802.696054] usb 4-2: device not accepting address 2, error -71
[ 802.808040] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 803.216023] usb 4-2: device not accepting address 2, error -71
[ 803.216080] usb 4-2: USB disconnect, address 2
[ 803.218844] scsi 2:0:0:0: rejecting I/O to dead device
[ 803.332057] usb 4-2: new full speed USB device using uhci_hcd and address 3
[ 803.452025] usb 4-2: device descriptor read/64, error -71
[ 803.676063] usb 4-2: device descriptor read/64, error -71
[ 803.892023] usb 4-2: new full speed USB device using uhci_hcd and address 4
[ 804.012037] usb 4-2: device descriptor read/64, error -71
[ 804.236061] usb 4-2: device descriptor read/64, error -71
[ 804.452022] usb 4-2: new full speed USB device using uhci_hcd and address 5
[ 804.860022] usb 4-2: device not accepting address 5, error -71
[ 804.972024] usb 4-2: new full speed USB device using uhci_hcd and address 6
[ 805.380035] usb 4-2: device not accepting address 6, error -71
[ 805.380064] hub 4-0:1.0: unable to enumerate USB device on port 2
[ 812.216979] usbcore: registered new interface driver usbserial
[ 812.217042] USB Serial support registered for generic
[ 812.219919] usbcore: registered new interface driver usbserial_generic
[ 812.219929] usbserial: USB Serial Driver core
[ 816.228025] usb 4-2: new full speed USB device using uhci_hcd and address 7
[ 816.352015] usb 4-2: device descriptor read/64, error -71
[ 816.580021] usb 4-2: device descriptor read/64, error -71
[ 816.796017] usb 4-2: new full speed USB device using uhci_hcd and address 8
[ 816.920022] usb 4-2: device descriptor read/64, error -71
[ 817.144028] usb 4-2: device descriptor read/64, error -71
[ 817.360017] usb 4-2: new full speed USB device using uhci_hcd and address 9
[ 817.768041] usb 4-2: device not accepting address 9, error -71
[ 817.880026] usb 4-2: new full speed USB device using uhci_hcd and address 10
[ 818.288044] usb 4-2: device not accepting address 10, error -71
[ 818.288081] hub 4-0:1.0: unable to enumerate USB device on port 2



(txz)


User avatar
dhit

Post 08 Sep 2011, 16:57

mslah sya msh blm ad terselesaikan, g ad yg bntuin
help me please


User avatar
blackshirt
Contact:

Post 08 Sep 2011, 17:24

modemnya merk, tipe dan seri-nya apa gan ?? biar lebih jelas :d


User avatar
dhit

Post 08 Sep 2011, 17:52

bukan, modem sya kya air flash flexi yg warna hitam, klo modem kya gto sya udh berhasil conect , tp sya pinjem modem tmen..
modem sya kya gni,

http://www.google.co.id/imgres?imgurl=h ... rQfL273rCg


tp sya g tau tipe nya ap .. txz..


User avatar
blackshirt
Contact:

Post 08 Sep 2011, 18:49

saya rasa dengan prinsip yang sama, dengan model sejenis.. kalau sudah pernah sukses dengan yang putih, kan bisa dipelajari bagaimana caranya :d

semoga sukses :d


User avatar
dhit

Post 08 Sep 2011, 19:25

klo yg putih sm yg hitam memang nama nya sma, tp beda merk mas,
sy udh coba cara sma dgn yg putih, tp ttp aj g bsa, stiap hbs di sudo modprobe, modem jd g ke detect lg, sy itu bner2 baru pke linux, jd g tau... ..

tlong di bantu, . .


User avatar
blackshirt
Contact:

Post 08 Sep 2011, 20:48

mengutip dari http://groups.google.com/group/klub-lin ... 50b7a1d037
Jadi tahapan lengkapnya:
1. Colok modem CDMA Air Flash SX0301 ke PC
2. # eject /dev/sr1
3. Lakukan dmesg untuk mendapatkan nomor vendor&product: # dmesg
4. # modprobe usbserial vendor=0x??? Product=0x2008
5. # system-config-network
6. Di bagian perangkat keras tambahin modem, /dev/ttyUSB0
baudrate tetep 460800 dan lain2x biarin
7. Di bagian perangkat tambahin koneksi baru no telp #777
user pass isi, trus next dan simpan
8. Lalu silakan koneksikan dari applet network manager yg di pojok kanan.
8. Selesai
note :
- /dev/sr1 atau yang lain tergantung oleh "dikenalinya" oleh kernel
- vendor dan product juga harus disesuaikan
- system-config-network umumnya spesifik ke distro "redhat-based", kita bisa mengubah wvdial.conf untuk konfig tersebut.


User avatar
dhit

Post 08 Sep 2011, 22:08

maaf mas, sewaktu sya ketik eject /dev/sr1 di terminal, ada bacaan gni mas ..
eject: unable to find or open device for: '/dev/sr1'.

trs stiap hbs sya ketik sudo modprobe, modem jd g ke detect di lsusb ..

sekalian sya mau tnya, guna nya usb_modeswitch itu utk ap ya,..

txz
(apa pun sya coba asal sya bisa conect internet di ubuntu)


User avatar
k4341
Contact:

Post 09 Sep 2011, 05:21

bro coba tes modemnya di pasang di windows masih bisa jalan ga..?


User avatar
yudiarbi
Contact:

Post 09 Sep 2011, 23:42

cobain ya...
[spoiler]1. Colok modem nya ke USB dulu
2. Trus kalo udah, sebagai root (sudo su) di terminal ketik �lsusb� yang kurang lebih akan memunculkan daftar device yang di colok ke usb. Punya ku seperti ini, punya kelian mungkin beda dan setiap jenis modem pastinya beda kecuali kalo sama mereknya:

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 2015:0001
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

3. misal Modem kedetek di barus ketiga. Abis tu langsung aja sebagai root kita �modprobe� pake perintah:

modprobe usbserial vendor=0�2015 product=0�0001

4. ok kalo udah lakukan perintah diatas, untuk memastikan modem ke detect coba di terminal ketik �wvdialconf� , kalo modemnya ga kedetek, loh? bukannya udah di �modprobe�? Iya sih, tapi jadi inget dulu waktu di colok ke laptop yang pake Windows XP, modem tersebut kedetek sebagai CD-ROM. Loh? iyakan�coba?..coba deh diinget2� Modem CDMA bonus CD-ROM? Lalu gimana mau make modemnya? Tentunya harus di remove dulu dong fungsi modem ini yang sebagai CD-ROM�caranya begini� kita dmesg | grep �CD-ROM� aja biar kita tau device nya yang mana. Ini punya saya, punya kalian mungkin berbeda�

linux@ubuntu:~$ dmesg | grep �CD-ROM�

atau pada beberapa distro linux kadang kita pakai �CDROM�

[ 1.516745] scsi 1:0:0:0: CD-ROM SONY DVD RW DRU-830A SS25 PQ: 0 ANSI: 5
[ 1.523752] Uniform CD-ROM driver Revision: 3.20
[ 1.523947] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.534876] scsi 1:0:1:0: CD-ROM LITE-ON LTR-48246S SS0E PQ: 0 ANSI: 5
[ 1.585218] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 2101.223348] scsi 2:0:0:0: CD-ROM Qualcomm MMC Storage 2.31 PQ: 0 ANSI: 2
[ 2101.271068] sr 2:0:0:0: Attached scsi CD-ROM sr2

5. Sekarang modemnya kedetek di sr2, la itu scsi CD-ROM sr2,tergantung vendero di kenal sebagai storagenya

nah sekarang kita mesti eject tapi mesti sebagai root

linux@ubuntu:~$ eject /dev/sr2″.

6. Nah sekarang untuk menseting modem! kita harus lakukan perintah di terminal sebagai root yaitu �wvdialconf� dulu. Abis itu baru den modem bisa di gunakan.
7. Namun sekarang kita mesti edit file wvdial.conf sebelum kita dapat menggunakannya

linux@ubuntu:~$ sudo gedit /etc/wvdial.conf

dan jangan lupa pada bagian username dan passwordnya diisi sesuai seting operator kita

berikut contohnya :

[Dialer Defaults]
Modem = /dev/ttyUSB0
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid mode = 1 // hanya ditambahkan jika modem ga konek tapi kalo konek hilangkan saja�
Modem Type = Analog Modem
Phone = #777
New PPPD = yes
ISDN = 0
Username = smart
Password = smart
Baud = 9600

Kalo udah baru deh jalankan di terminal sebagai root perintah �wvdial�

linux@ubuntu:~$ sudo wvdial[/spoiler]

ok deh akhirna bisa deh internetan� hee�


User avatar
dhit

Post 11 Sep 2011, 21:04

ok txz, akn sy coba dlu,..
tp maaf mas, sya mau tnya ttg ini
Linux@Ubuntu:~$ eject /dev/sr2″
itu sr2″ di dpat dri mna ya ..


User avatar
dhit

Post 11 Sep 2011, 22:22

mas ttp g bsa, hbs ketik
eject /dev/sr1″
(di sya ke detect sr1)

ttp ada bacaan
eject: unable to find or open device for: '/dev/sr1'.


User avatar
dhit

Post 12 Sep 2011, 12:02

mohon bantuan nya


User avatar
Nexus

Post 12 Sep 2011, 12:18

coba cek di-synaptic, ketik kata modem dlm kolom pencarian, yg terinstall dari pencarian kata MODEM apa aja??.


User avatar
dhit

Post 12 Sep 2011, 22:40

ini mas, sya catat aja smua nya ...

Modemmanager
pppconfig
gnome-applets
ppp
usb-modeswitch-data
pcmciautils
(status : installed)


wvdial (status : marked for upgrade)


kppp-kde4
usb-modeswitch
(status : marked for removal)


gnome-ppp
dhcp3-client
(status : installed(upgradable) )


User avatar
Nexus

Post 12 Sep 2011, 22:51

1. ada yg kurang tuh. punya ente inikan:

- Modemmanager
- pppconfig
- gnome-applets
- ppp
- usb-modeswitch-data
- pcmciautils
(status : installed)

>> yg kurang:

- isc-dhcp-client
- usb-modeswitch
- sl-modem-daemon
- gobi-loader

>>> trus ente pake kde (kubuntu), kok ada:
- kppp

>> kalo pake gnome, pake yg ppp udah cukup.

>>> trus kok ada gnome-ppp n dhcp3-client??.. ppp bawaan n isc-dhcp-client udah cukup


User avatar
dhit

Post 12 Sep 2011, 23:17

trs sya msti gmna mas,.
mas nanya trs, maklum newbie


User avatar
k4341
Contact:

Post 13 Sep 2011, 13:59

bro di windows dah di coba, bisa konek ga..? masalah nya ada error ini mungkin hardwarenya rusak atau emang ga suport ama linux.

Code: Select all

[ 769.897911] sr: Sense Key : Hardware Error [current]
[ 769.897918] sr: Add. Sense: No additional sense information
[ 770.012120] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.168030] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.288026] usb 4-2: device descriptor read/64, error -71
[ 801.512040] usb 4-2: device descriptor read/64, error -71
[ 801.728054] usb 4-2: reset full speed USB device using uhci_hcd and address 2
[ 801.848037] usb 4-2: device descriptor read/64, error -71
[ 802.072047] usb 4-2: device descriptor read/64, error -71
kalo eject /dev/sr1 menurut ane itu dah bener

Code: Select all

[ 767.829011] scsi 2:0:0:0: CD-ROM EVDO MMC Storage 2.31 PQ: 0 ANSI: 2
[ 767.853987] sr1: scsi-1 drive
[ 767.854243] sr 2:0:0:0: Attached scsi CD-ROM sr1
[ 767.854383] sr 2:0:0:0: Attached scsi generic sg2 type 5
Sorry ini cuman asumsi ane.. mohon koreksi kalau salah

cara bro blackshirt udah di coba..?
sebagai tambahan cara bro black itu, nt haru sebagai root/super user. colokin modem tunggu beberapa saat kemudian buka terminal masukan perintah di bawah ini "jangan ketinggalan sudo nya".

sudo eject /dev/sr1
sudo modprobe usbserial vendor=0x1c9e product=0x6000

kemudian lihat network-manager "udah kedetek belom..?" kalo blom dikonekin pake wvdial

sudo wvdialconf
sudo wvdial


User avatar
terusbelajar

Post 13 Sep 2011, 14:22

atau mungkin bisa dicoba mencolokkan modemmnya sebelum PC/lepienya diidupin...
Barangkali sedikit berpengaruh :D


User avatar
Nexus

Post 13 Sep 2011, 15:17

dhit wrote:trs sya msti gmna mas,.
mas nanya trs, maklum newbie
kok malah nanya, ente tuh pakai ubuntu apa kubuntu??.. kalo pakai ubuntu yg kurang diinstall n yg versi buat kubuntu dihapus.

>> punya ente inikan:

- Modemmanager
- pppconfig
- gnome-applets
- ppp
- usb-modeswitch-data
- pcmciautils
(status : installed)

>> yg kurang, dibawah ini yg harus diinstall:

- isc-dhcp-client
- usb-modeswitch
- sl-modem-daemon
- gobi-loader

>> kalo pake ubuntu, yg versi kubuntu ini n yg gak perlu dihapus aja:

- kppp (diremove)
- gnome-ppp (diremove)
- dhcp3-client (diremove)

>>>>dari synaptic aja installnya.. abis install dari synaptic, lalu close synaptic n masuk terminal. lalu command:

sudo apt-get install --fix-missing
sudo apt-get update --fix-missing
sudo apt-get upgrade --fix-missing
sudo apt-get dist-upgrade --fix-missing

>> kalo ada yg missing (hilang) bisa dibenerin dari command itu, kalo gak ada reaksi apa2, yaa langsung direstart aja.


User avatar
dhit

Post 14 Sep 2011, 17:58

nexus@sya pke ubuntu 10.10,
maaf mas, sya kan blm konek internet, mang bsa ya instal/update..


k4341@sya udh coba pke diwindows, modem berjalan normal...

maaf nie ngrepotin rekan2 forum
txz


User avatar
Nexus

Post 14 Sep 2011, 20:03

makanya cari koneksi internet dulu.. :grin:


User avatar
dhit

Post 14 Sep 2011, 21:14

mas, udh sya lakuin ap yg mas nexus suruh, tp ttp g bsa mas ..
sprti biasa, modem habs di modprobe, lgsung ilang, jd g ke detect..


User avatar
k4341
Contact:

Post 14 Sep 2011, 21:48

bro perintah modprobe sesudah eject apa sebelumnya, kalo menurut ane sesudah eject /dev/sr1.

kalo masih blom konek mungkin karakternya sama dg modem smart d1200p, harus di pancing pake windows.
caranya
1. konekin modem di windows terus diskonek.
2. reboot windows dan masuk ke ubuntu
3. di ubuntu buka terminal
4. sudo eject /dev/sr1
5. lsusb
6. sudo modprobe usbserial vendor=0x**** product=0x****
7. sudo wvdialconf
8. sudo wvdial

NB.isi modprobe tergantung pada hasil lsusb setelah di eject /dev/sr1
jika nt pake flexi"unlimit" maka passwd n user berbeda pada tiap user.
kalo masih belum konek ane angkat tangan dulu...


User avatar
dhit

Post 14 Sep 2011, 22:12

perintah modprobe di lakukan setelah & sesudah eject, udh sya coba semua, tp ttp g konek,
coba pke ubuntu,tp sm jg bhong kl g bsa OL.
klo di lakukan perintah eject, ada bacaan gni
eject: unable to find or open device for: '/dev/sr1'.


User avatar
k4341
Contact:

Post 14 Sep 2011, 22:37

Code: Select all

eject: unable to find or open device for: '/dev/sr1'.
ini berarti modem blom terdetek sebagai sr1 coba nt cek lagi dengan perintah "dmesg | tail sr*" dan "ls /dev/sr*" bisa juga error kayak gitu karena memberikan perintah sebagai user biasa bukan root.


User avatar
dhit

Post 14 Sep 2011, 22:51

sya coba,
smga berhasil..
tp maaf, sya mau tnya,
perintah "dmesg | tail sr*" dan "ls /dev/sr*" itu fungsi nya buat ap ya ..
txz


User avatar
k4341
Contact:

Post 14 Sep 2011, 23:26

dmesg | tail sr* = melihat log/catatan kegiatan terbaru yang ada susunan huruf sr....
ls /dev/sr* = untuk melihat isi folder /dev yang di awali sr....
* = menunjukan karakter,angka atau huruf apa saja sebelum "*"
contoh = sr* menunjukan apaun yang di awali oleh sr....

NB. bagi pengguna windows dan masih baru dg Linux biasanya risih dg pengunaan root/sudo yang harus memasukan passwd, tapi itu untuk keamanan system agar ga bisa di utak-atik oleh sembarang user.


User avatar
dhit

Post 16 Sep 2011, 11:58

mas ttp g bsa, prtma memang ter detect di sr1,
tp g lma hilang lg . . .
knpa ya,...
sya bner2 msh penasaran
ini perintah dmesg | tail sr*

root@fuck:/home/umbara# dmesg | tail sr*
tail: cannot open `sr*' for reading: No such file or directory


User avatar
k4341
Contact:

Post 16 Sep 2011, 15:20

sory bro salah perintah yang bener
dmesg | grep sr*


User avatar
dhit

Post 18 Sep 2011, 19:30

trs ap lg mas bro stelah sya lakukan kya gto . .
txz


User avatar
k4341
Contact:

Post 18 Sep 2011, 19:51

ini masih seputar eject sr* kalo udah berhasil eject mungkin bisa di teruskan ke modprobe.

atau pake perkiraan aja eject semua dev/srnya dengan mengetikan semua perintah
sudo eject /dev/sr0
sudo eject /dev/sr1
sudo eject /dev/sr2
dan "dmesg | grep sr" keluarnya apa..?


Post Reply

Who is online

Users browsing this forum: No registered users and 17 guests