[Tanya] Instalasi modem geemobile

Membahas Perangkat-perangkat keras yang belum dideteksi dengan baik oleh Ubuntu serta solusinya.
User avatar
stufi
Posts: 3
Joined: 27 Aug 2010, 04:10

[Tanya] Instalasi modem geemobile

Postby stufi » 27 Aug 2010, 04:33

Mohon petunjuk instalasi modem gee mobile (CDMA). Waktu saya tancapkan modem di usb tidak terjadi apa apa di ubuntu. Lalu saya coba masuk terminal dan ketik lsusb namun malah hang dan akhirnya saya cabut lagi dan tampil daftar usb-nya.

Kemudian saya reboot dan tancapkan usb waktu booting ubuntu, pun tidak terjadi apa-apa. Lalu saya coba ke terminal lihat lsusb dan muncul:

Bus 002 Device 004: ID 05c6:1000 Qualcomm, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 0db0:6877 Micro Star International RT2573
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

tapi saya lihat di ls /dev/ttyUSB* tidak muncul apa-apa

Lalu saya coba modprobe -v product=0x1000 vendor=0x05c6 dan ternyata tidak muncul apa-apa, saya ls /dev/ttyUSB* pun tidak ada

saya cari di forum2 lalu coba usb_modeswitch dan memasukkan /etc/usb-modeswitch.conf tulisan

DefaultVendor= 0x05c6
DefaultProduct= 0x1000
MessageContent="5553424360953886000000000000061b010000000000000000000000000000"

namun setelah lsusb tetap sama dan ls /dev/ttyUSB* tetap tidak muncul apa-apa.

Kemudian saya mencoba di windows dan install aplikasinya dan setelah saya liat di device manager windows, modemnya memiliki VID:05c6 dan PID:6500

Saya tidak mengerti bagaimana cara mendapatkan value MessageContent agar modem bisa switch dari storage menjadi modem. Mohon bantuannya
User avatar
stufi
Posts: 3
Joined: 27 Aug 2010, 04:10

Re: [Tanya] Instalasi modem geemobile

Postby stufi » 27 Aug 2010, 07:16

dmesg saat ditancapkan ke komputer:
[ 109.700144] usb 2-1: new full speed USB device using ohci_hcd and address 2
[ 109.930218] usb 2-1: configuration #1 chosen from 1 choice
[ 240.580156] INFO: task modem-modeswitc:1921 blocked for more than 120 seconds.
[ 240.580167] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.580174] modem-modeswi D 0000000000000000 0 1921 1672 0x00000000
[ 240.580186] ffff8800582adcc8 0000000000000086 0000000000015bc0 0000000000015bc0
[ 240.580198] ffff880058035f80 ffff8800582adfd8 0000000000015bc0 ffff880058035bc0
[ 240.580208] 0000000000015bc0 ffff8800582adfd8 0000000000015bc0 ffff880058035f80
[ 240.580217] Call Trace:
[ 240.580240] [] schedule_timeout+0x22d/0x300
[ 240.580254] [] ? chrdev_open+0x13a/0x240
[ 240.580264] [] ? chrdev_open+0x0/0x240
[ 240.580273] [] __down+0x7e/0xc0
[ 240.580285] [] down+0x41/0x50
[ 240.580298] [] usbdev_ioctl+0x76/0xfb0
[ 240.580307] [] ? lru_cache_add_lru+0x21/0x40
[ 240.580317] [] ? do_anonymous_page+0x11b/0x310
[ 240.580327] [] vfs_ioctl+0x7c/0xa0
[ 240.580336] [] do_vfs_ioctl+0x81/0x380
[ 240.580344] [] sys_ioctl+0x81/0xa0
[ 240.580356] [] system_call_fastpath+0x16/0x1b
[ 289.117148] scsi4 : SCSI emulation for USB Mass Storage devices
[ 289.117689] usb 2-1: USB disconnect, address 2
[ 289.117744] usb-storage: device found at 2
[ 289.117749] usb-storage: waiting for device to settle before scanning
[ 407.450146] usb 2-2: new full speed USB device using ohci_hcd and address 3
[ 407.680501] usb 2-2: configuration #1 chosen from 1 choice
[ 446.048415] scsi5 : SCSI emulation for USB Mass Storage devices
[ 446.048959] usb-storage: device found at 3
[ 446.048964] usb-storage: waiting for device to settle before scanning
[ 446.050274] usb 2-2: USB disconnect, address 3
[ 450.500881] usb 2-2: new full speed USB device using ohci_hcd and address 4
[ 450.729993] usb 2-2: configuration #1 chosen from 1 choice


hasil lsusb:
Komputer Hang (diam aja tidak keluar daftar usb)


hasil lsusb setelah modem dicabut:
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0db0:6877 Micro Star International RT2573
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

NB:
Sesaat setelah ditancapkan lampu berwarna merah, lalu beberapa detik kemudian berwarna hijau. Baik saat lampu berwarna merah maupun hijau lsusb sama-sama hang.


SEdangkan bila ditancapkan sebelum dinyalanyan laptonya, saat dmesg:
[ 0.100000] ...trying to set up timer (IRQ0) through the 8259A ...
[ 0.100000] ..... (found apic 0 pin 0) ...
[ 0.120000] ....... failed.
[ 0.120000] ...trying to set up timer as Virtual Wire IRQ...
[ 0.120000] ..... failed.
[ 0.120000] ...trying to set up timer as ExtINT IRQ...
[ 0.229368] ..... works.
[ 0.229372] CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02
[ 0.230000] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.030000] Initializing CPU#1
[ 0.030000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 0.030000] CPU: L2 Cache: 256K (64 bytes/line)
[ 0.030000] CPU 1/0x1 -> Node 0
[ 0.030000] CPU: Physical Processor ID: 0
[ 0.030000] CPU: Processor Core ID: 1
[ 0.380082] CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02
[ 0.030000] System has AMD C1E enabled
[ 0.380115] Brought up 2 CPUs
[ 0.380122] Total of 2 processors activated (3222.38 BogoMIPS).
[ 0.380111] Switch to broadcast mode on CPU1
[ 0.380499] CPU0 attaching sched-domain:
[ 0.380507] domain 0: span 0-1 level MC
[ 0.380513] groups: 0 1
[ 0.380527] CPU1 attaching sched-domain:
[ 0.380532] domain 0: span 0-1 level MC
[ 0.380537] groups: 1 0
[ 0.380761] Switch to broadcast mode on CPU0
[ 0.380761] devtmpfs: initialized
[ 0.380761] regulator: core version 0.5
[ 0.380761] Time: 23:37:32 Date: 08/26/10
[ 0.380761] NET: Registered protocol family 16
[ 0.380761] Trying to unpack rootfs image as initramfs...
[ 0.380761] node 0 link 0: io port [1000, ffffff]
[ 0.380761] TOM: 0000000080000000 aka 2048M
[ 0.380761] node 0 link 0: mmio [e0000000, efffffff]
[ 0.380761] node 0 link 0: mmio [a0000, bffff]
[ 0.380761] node 0 link 0: mmio [80000000, fe0bffff]
[ 0.380761] bus: [00,ff] on node 0 link 0
[ 0.380761] bus: 00 index 0 io port: [0, ffff]
[ 0.380761] bus: 00 index 1 mmio: [80000000, fcffffffff]
[ 0.380761] bus: 00 index 2 mmio: [a0000, bffff]
[ 0.380761] ACPI: bus type pci registered
[ 0.380808] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.380815] PCI: Not using MMCONFIG.
[ 0.380820] PCI: Using configuration type 1 for base access
[ 0.390326] bio: create slab at 0
[ 0.393022] ACPI: EC: Look up EC in DSDT
[ 0.396238] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.418917] ACPI: Interpreter enabled
[ 0.418932] ACPI: (supports S0 S3 S4 S5)
[ 0.418994] ACPI: Using IOAPIC for interrupt routing
[ 0.419134] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.427909] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.444109] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.464663] ACPI: EC: GPE = 0x22, I/O: command/status = 0x66, data = 0x62
[ 0.464918] ACPI Warning: Incorrect checksum in table [OEMB] - A2, should be 9E (20090903/tbutils-314)
[ 0.466258] ACPI: No dock devices found.
[ 0.466599] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.467183] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.467191] pci 0000:00:02.0: PME# disabled
[ 0.467283] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.467291] pci 0000:00:03.0: PME# disabled
[ 0.467347] pci 0000:00:05.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[ 0.467361] pci 0000:00:05.0: reg 14 64bit mmio pref: [0xb0000000-0xbfffffff]
[ 0.467374] pci 0000:00:05.0: reg 1c 64bit mmio: [0xfc000000-0xfcffffff]
[ 0.467387] pci 0000:00:05.0: reg 30 32bit mmio pref: [0xfe2e0000-0xfe2fffff]
[ 0.467699] HPET not enabled in BIOS. You might try hpet=force boot option
[ 0.467782] pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
[ 0.467795] pci 0000:00:0a.1: reg 24 io port: [0x6000-0x603f]
[ 0.467837] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[ 0.467848] pci 0000:00:0a.1: PME# disabled
[ 0.467903] pci 0000:00:0a.3: reg 10 32bit mmio: [0xd0000000-0xd003ffff]
[ 0.468054] pci 0000:00:0b.0: reg 10 32bit mmio: [0xfe2de000-0xfe2defff]
[ 0.468118] pci 0000:00:0b.0: supports D1 D2
[ 0.468124] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.468132] pci 0000:00:0b.0: PME# disabled
[ 0.468191] pci 0000:00:0b.1: reg 10 32bit mmio: [0xfe2dfc00-0xfe2dfcff]
[ 0.468258] pci 0000:00:0b.1: supports D1 D2
[ 0.468263] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.468271] pci 0000:00:0b.1: PME# disabled
[ 0.468357] pci 0000:00:0d.0: reg 20 io port: [0xffa0-0xffaf]
[ 0.468460] pci 0000:00:0e.0: reg 10 io port: [0xd800-0xd807]
[ 0.468472] pci 0000:00:0e.0: reg 14 io port: [0xd480-0xd483]
[ 0.468483] pci 0000:00:0e.0: reg 18 io port: [0xd400-0xd407]
[ 0.468495] pci 0000:00:0e.0: reg 1c io port: [0xd080-0xd083]
[ 0.468507] pci 0000:00:0e.0: reg 20 io port: [0xd000-0xd00f]
[ 0.468518] pci 0000:00:0e.0: reg 24 32bit mmio: [0xfe2dd000-0xfe2ddfff]
[ 0.468724] pci 0000:00:10.1: reg 10 32bit mmio: [0xfe2d8000-0xfe2dbfff]
[ 0.468796] pci 0000:00:10.1: PME# supported from D3hot D3cold
[ 0.468805] pci 0000:00:10.1: PME# disabled
[ 0.468881] pci 0000:00:14.0: reg 10 32bit mmio: [0xfe2dc000-0xfe2dcfff]
[ 0.468892] pci 0000:00:14.0: reg 14 io port: [0xcc00-0xcc07]
[ 0.468944] pci 0000:00:14.0: supports D1 D2
[ 0.468950] pci 0000:00:14.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.468958] pci 0000:00:14.0: PME# disabled
[ 0.469240] pci 0000:00:02.0: bridge io port: [0xb000-0xbfff]
[ 0.469248] pci 0000:00:02.0: bridge 32bit mmio: [0xf9f00000-0xfa1fffff]
[ 0.469399] pci 0000:03:05.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.469412] pci 0000:03:05.0: reg 14 32bit mmio: [0xfe3fe000-0xfe3fe7ff]
[ 0.469473] pci 0000:03:05.0: supports D1 D2
[ 0.469478] pci 0000:03:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.469487] pci 0000:03:05.0: PME# disabled
[ 0.469546] pci 0000:03:05.2: reg 10 32bit mmio: [0xfe3fec00-0xfe3fecff]
[ 0.469616] pci 0000:03:05.2: supports D1 D2
[ 0.469621] pci 0000:03:05.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.469630] pci 0000:03:05.2: PME# disabled
[ 0.469687] pci 0000:03:05.3: reg 10 32bit mmio: [0xfe3ff000-0xfe3fffff]
[ 0.469757] pci 0000:03:05.3: supports D1 D2
[ 0.469762] pci 0000:03:05.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.469771] pci 0000:03:05.3: PME# disabled
[ 0.469838] pci 0000:00:10.0: transparent bridge
[ 0.469846] pci 0000:00:10.0: bridge io port: [0xe000-0xefff]
[ 0.469855] pci 0000:00:10.0: bridge 32bit mmio: [0xfe300000-0xfebfffff]
[ 0.469864] pci 0000:00:10.0: bridge 32bit mmio pref: [0xce000000-0xcfffffff]
[ 0.469896] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.470525] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.470723] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.471021] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 0.512247] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.512830] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *10
[ 0.513400] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.513972] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.514545] ACPI: PCI Interrupt Link [LNEA] (IRQs 16 17 18 19) *0, disabled.
[ 0.515118] ACPI: PCI Interrupt Link [LNEB] (IRQs 16 17 18 19) *0, disabled.
[ 0.520419] ACPI: PCI Interrupt Link [LNEC] (IRQs 16 17 18 19) *10
[ 0.520997] ACPI: PCI Interrupt Link [LNED] (IRQs 16 17 18 19) *0, disabled.
[ 0.521573] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *7
[ 0.522147] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *14
[ 0.522750] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *5
[ 0.523329] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
[ 0.523902] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *0, disabled.
[ 0.524478] ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled.
[ 0.525063] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *5
[ 0.525639] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *11
[ 0.526212] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *10
[ 0.526787] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *0, disabled.
[ 0.527467] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.527770] vgaarb: device added: PCI:0000:00:05.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.527805] vgaarb: loaded
[ 0.528089] SCSI subsystem initialized
[ 0.530161] libata version 3.00 loaded.
[ 0.530353] usbcore: registered new interface driver usbfs
[ 0.530390] usbcore: registered new interface driver hub
[ 0.530457] usbcore: registered new device driver usb
[ 0.530841] ACPI: WMI: Mapper loaded
[ 0.530845] PCI: Using ACPI for IRQ routing
[ 0.531281] NetLabel: Initializing
[ 0.531285] NetLabel: domain hash size = 128
[ 0.531289] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.531324] NetLabel: unlabeled traffic allowed by default
[ 0.535945] AppArmor: AppArmor Filesystem Enabled
[ 0.536003] pnp: PnP ACPI init
[ 0.536045] ACPI: bus type pnp registered
[ 0.543924] pnp: PnP ACPI: found 12 devices
[ 0.543931] ACPI: ACPI bus type pnp unregistered
[ 0.544716] system 00:07: iomem range 0xfefe0000-0xfefe01ff has been reserved
[ 0.544733] system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.544742] system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.544761] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[ 0.544769] system 00:09: ioport range 0x800-0x80f has been reserved
[ 0.544777] system 00:09: ioport range 0x4000-0x407f has been reserved
[ 0.544785] system 00:09: ioport range 0x4080-0x40ff has been reserved
[ 0.544792] system 00:09: ioport range 0x4400-0x447f has been reserved
[ 0.544800] system 00:09: ioport range 0x4480-0x44ff has been reserved
[ 0.544808] system 00:09: ioport range 0x4800-0x487f has been reserved
[ 0.544816] system 00:09: ioport range 0x4880-0x48ff has been reserved
[ 0.544824] system 00:09: ioport range 0x2000-0x207f has been reserved
[ 0.544831] system 00:09: ioport range 0x2080-0x20ff has been reserved
[ 0.544840] system 00:09: iomem range 0xfee01000-0xfeefffff has been reserved
[ 0.544869] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.544884] system 00:0b: iomem range 0x0-0x9ffff could not be reserved
[ 0.544892] system 00:0b: iomem range 0xc0000-0xcffff has been reserved
[ 0.544899] system 00:0b: iomem range 0xe0000-0xfffff could not be reserved
[ 0.544907] system 00:0b: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.544915] system 00:0b: iomem range 0xfec00000-0xffffffff could not be reserved
[ 0.551303] Switching to clocksource acpi_pm
[ 0.551761] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
[ 0.551761] pci 0000:00:02.0: IO window: 0xb000-0xbfff
[ 0.551761] pci 0000:00:02.0: MEM window: 0xf9f00000-0xfa1fffff
[ 0.551761] pci 0000:00:02.0: PREFETCH window: 0x0000007c000000-0x0000007c1fffff
[ 0.551761] pci 0000:00:03.0: PCI bridge, secondary bus 0000:02
[ 0.551761] pci 0000:00:03.0: IO window: 0x1000-0x1fff
[ 0.551761] pci 0000:00:03.0: MEM window: 0x7c200000-0x7c3fffff
[ 0.551761] pci 0000:00:03.0: PREFETCH window: 0x0000007c400000-0x0000007c5fffff
[ 0.551761] pci 0000:00:10.0: PCI bridge, secondary bus 0000:03
[ 0.551761] pci 0000:00:10.0: IO window: 0xe000-0xefff
[ 0.551761] pci 0000:00:10.0: MEM window: 0xfe300000-0xfebfffff
[ 0.551761] pci 0000:00:10.0: PREFETCH window: 0xce000000-0xcfffffff
[ 0.551761] pci 0000:00:02.0: setting latency timer to 64
[ 0.551761] pci 0000:00:03.0: enabling device (0004 -> 0007)
[ 0.551761] pci 0000:00:03.0: setting latency timer to 64
[ 0.551761] pci 0000:00:10.0: setting latency timer to 64
[ 0.551761] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.551761] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.551761] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.551761] pci_bus 0000:01: resource 1 mem: [0xf9f00000-0xfa1fffff]
[ 0.551761] pci_bus 0000:01: resource 2 pref mem [0x7c000000-0x7c1fffff]
[ 0.551761] pci_bus 0000:02: resource 0 io: [0x1000-0x1fff]
[ 0.551761] pci_bus 0000:02: resource 1 mem: [0x7c200000-0x7c3fffff]
[ 0.551761] pci_bus 0000:02: resource 2 pref mem [0x7c400000-0x7c5fffff]
[ 0.551761] pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
[ 0.551761] pci_bus 0000:03: resource 1 mem: [0xfe300000-0xfebfffff]
[ 0.551761] pci_bus 0000:03: resource 2 pref mem [0xce000000-0xcfffffff]
[ 0.551761] pci_bus 0000:03: resource 3 io: [0x00-0xffff]
[ 0.551761] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.551761] NET: Registered protocol family 2
[ 0.551761] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.553470] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.558039] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.559316] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.559324] TCP reno registered
[ 0.559585] NET: Registered protocol family 1
[ 0.559720] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.559775] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.559790] pci 0000:00:05.0: Boot video device
[ 0.910203] pci 0000:00:09.0: Found enabled HT MSI Mapping
[ 0.910297] pci 0000:00:09.0: Found enabled HT MSI Mapping
[ 0.910394] pci 0000:00:09.0: Found enabled HT MSI Mapping
[ 0.911240] Scanning for low memory corruption every 60 seconds
[ 0.911594] audit: initializing netlink socket (disabled)
[ 0.911621] type=2000 audit(1282865851.902:1): initialized
[ 0.935224] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.939106] VFS: Disk quotas dquot_6.5.2
[ 0.939288] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.940983] fuse init (API version 7.13)
[ 0.941206] msgmni has been set to 3873
[ 0.941840] alg: No test for stdrng (krng)
[ 0.942015] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.942022] io scheduler noop registered
[ 0.942027] io scheduler anticipatory registered
[ 0.942031] io scheduler deadline registered
[ 0.942138] io scheduler cfq registered (default)
[ 0.942573] alloc irq_desc for 24 on node 0
[ 0.942579] alloc kstat_irqs on node 0
[ 0.942598] pcieport 0000:00:02.0: irq 24 for MSI/MSI-X
[ 0.942611] pcieport 0000:00:02.0: setting latency timer to 64
[ 0.942914] alloc irq_desc for 25 on node 0
[ 0.942919] alloc kstat_irqs on node 0
[ 0.942931] pcieport 0000:00:03.0: irq 25 for MSI/MSI-X
[ 0.942941] pcieport 0000:00:03.0: setting latency timer to 64
[ 0.943128] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.943349] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.944140] ACPI: AC Adapter [AC] (on-line)
[ 0.944364] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:04/PNP0C0D:00/input/input0
[ 0.944464] ACPI: Lid Switch [LIDD]
[ 0.944596] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 0.944611] ACPI: Sleep Button [SLPB]
[ 0.944719] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 0.944725] ACPI: Power Button [PWRB]
[ 0.944833] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.944839] ACPI: Power Button [PWRF]
[ 0.945864] ACPI: processor limited to max C-state 1
[ 0.945945] processor LNXCPU:00: registered as cooling_device0
[ 0.946038] processor LNXCPU:01: registered as cooling_device1
[ 0.959436] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.959462] ACPI: Thermal Zone [THRM] (47 C)
[ 0.963299] Linux agpgart interface v0.103
[ 0.963419] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.966601] brd: module loaded
[ 0.967854] loop: module loaded
[ 0.968112] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.968733] pata_acpi 0000:00:0d.0: setting latency timer to 64
[ 0.969771] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 0.969783] alloc irq_desc for 23 on node 0
[ 0.969788] alloc kstat_irqs on node 0
[ 0.969812] pata_acpi 0000:00:0e.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[ 0.969881] pata_acpi 0000:00:0e.0: setting latency timer to 64
[ 0.969905] pata_acpi 0000:00:0e.0: PCI INT A disabled
[ 0.970980] Fixed MDIO Bus: probed
[ 0.971066] PPP generic driver version 2.4.2
[ 0.971202] tun: Universal TUN/TAP device driver, 1.6
[ 0.971207] tun: (C) 1999-2004 Max Krasnyansky
[ 0.971445] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.972464] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[ 0.972477] alloc irq_desc for 22 on node 0
[ 0.972482] alloc kstat_irqs on node 0
[ 0.972506] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.972559] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[ 0.972568] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 0.972697] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 0.972767] ehci_hcd 0000:00:0b.1: debug port 1
[ 0.972782] ehci_hcd 0000:00:0b.1: cache line size of 64 is not supported
[ 0.972830] ehci_hcd 0000:00:0b.1: irq 22, io mem 0xfe2dfc00
[ 1.000085] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 1.000388] usb usb1: configuration #1 chosen from 1 choice
[ 1.000461] hub 1-0:1.0: USB hub found
[ 1.000483] hub 1-0:1.0: 6 ports detected
[ 1.000676] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.001688] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21
[ 1.001701] alloc irq_desc for 21 on node 0
[ 1.001707] alloc kstat_irqs on node 0
[ 1.001731] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[LUB0] -> GSI 21 (level, low) -> IRQ 21
[ 1.001772] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[ 1.001780] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 1.001949] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 1.002021] ohci_hcd 0000:00:0b.0: irq 21, io mem 0xfe2de000
[ 1.062342] usb usb2: configuration #1 chosen from 1 choice
[ 1.062424] hub 2-0:1.0: USB hub found
[ 1.062447] hub 2-0:1.0: 6 ports detected
[ 1.062640] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.062856] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.066024] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.067205] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.067221] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.067290] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.067348] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.067413] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.067741] mice: PS/2 mouse device common for all mice
[ 1.068234] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 1.068297] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 1.068652] device-mapper: uevent: version 1.0.3
[ 1.068988] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.069188] device-mapper: multipath: version 1.1.0 loaded
[ 1.069196] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.069608] cpuidle: using governor ladder
[ 1.069613] cpuidle: using governor menu
[ 1.070648] TCP cubic registered
[ 1.070979] NET: Registered protocol family 10
[ 1.072248] lo: Disabled Privacy Extensions
[ 1.073055] NET: Registered protocol family 17
[ 1.073147] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-50 processors (2 cpu cores) (version 2.20.00)
[ 1.073256] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x13
[ 1.073262] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e
[ 1.075679] PM: Resume from disk failed.
[ 1.075697] registered taskstats version 1
[ 1.076158] Magic number: 6:987:656
[ 1.076280] rtc_cmos 00:02: setting system clock to 2010-08-26 23:37:32 UTC (1282865852)
[ 1.076284] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.076286] EDD information not available.
[ 1.098372] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.157658] Freeing initrd memory: 8140k freed
[ 1.251341] ACPI: Battery Slot [BAT0] (battery present)
[ 1.341355] Freeing unused kernel memory: 880k freed
[ 1.341809] Write protecting the kernel read-only data: 7696k
[ 1.369813] udev: starting version 151
[ 1.382535] Clocksource tsc unstable (delta = 307131404 ns)
[ 1.505087] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1.505555] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 20
[ 1.505562] alloc irq_desc for 20 on node 0
[ 1.505565] alloc kstat_irqs on node 0
[ 1.505580] forcedeth 0000:00:14.0: PCI INT A -> Link[LMAC] -> GSI 20 (level, low) -> IRQ 20
[ 1.505587] forcedeth 0000:00:14.0: setting latency timer to 64
[ 1.505650] nv_probe: set workaround bit for reversed mac addr
[ 1.547242] ohci1394 0000:03:05.0: enabling device (0115 -> 0117)
[ 1.547982] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
[ 1.547989] alloc irq_desc for 19 on node 0
[ 1.547992] alloc kstat_irqs on node 0
[ 1.548008] ohci1394 0000:03:05.0: PCI INT A -> Link[LNKB] -> GSI 19 (level, low) -> IRQ 19
[ 1.622892] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[fe300000-fe3007ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 1.690096] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 1.974407] usb 1-6: configuration #1 chosen from 1 choice
[ 2.031277] forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:40:45:2d:ea:e4
[ 2.031283] forcedeth 0000:00:14.0: highdma pwrctl lnktim desc-v3
[ 2.031552] pata_amd 0000:00:0d.0: version 0.4.1
[ 2.031613] pata_amd 0000:00:0d.0: setting latency timer to 64
[ 2.031747] scsi0 : pata_amd
[ 2.031925] scsi1 : pata_amd
[ 2.034034] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.034038] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.034109] ata1: port disabled. ignoring.
[ 2.034310] sata_nv 0000:00:0e.0: version 3.5
[ 2.034324] sata_nv 0000:00:0e.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[ 2.034327] sata_nv 0000:00:0e.0: Using SWNCQ mode
[ 2.034392] sata_nv 0000:00:0e.0: setting latency timer to 64
[ 2.034569] scsi2 : sata_nv
[ 2.034718] scsi3 : sata_nv
[ 2.034981] ata3: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd000 irq 23
[ 2.034986] ata4: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xd008 irq 23
[ 2.210513] ata2.00: ATAPI: MATSHITADVD-RAM UJ-850S, 1.60, max UDMA/33
[ 2.210546] ata2: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000) ACPI=0x701f (60:900:0x11)
[ 2.250461] ata2.00: configured for UDMA/33
[ 2.253302] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-850S 1.60 PQ: 0 ANSI: 5
[ 2.259177] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.259181] Uniform CD-ROM driver Revision: 3.20
[ 2.259333] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.259421] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 2.310082] usb 2-2: new full speed USB device using ohci_hcd and address 2
[ 2.520152] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.540263] usb 2-2: configuration #1 chosen from 1 choice
[ 2.540570] ata3.00: ATA-7: FUJITSU MHV2080BHPL, 0081702E, max UDMA/100
[ 2.540574] ata3.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 2.551588] Initializing USB Mass Storage driver...
[ 2.557164] scsi4 : SCSI emulation for USB Mass Storage devices
[ 2.557292] usb-storage: device found at 2
[ 2.557296] usb-storage: waiting for device to settle before scanning
[ 2.557302] usbcore: registered new interface driver usb-storage
[ 2.557409] USB Mass Storage support registered.
[ 2.590587] ata3.00: configured for UDMA/100
[ 2.590711] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHV2080B 0081 PQ: 0 ANSI: 5
[ 2.590953] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.590974] sd 2:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.591094] sd 2:0:0:0: [sda] Write Protect is off
[ 2.591098] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.591131] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.591342] sda: sda1 sda2
[ 2.710603] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.931044] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.950303] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00012f65a1b7ff7f]
[ 4.230397] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 7.552228] usb-storage: device scan complete
[ 7.559164] scsi 4:0:0:0: CD-ROM Qualcomm MMC Storage 2.31 PQ: 0 ANSI: 0
[ 7.570131] sr1: scsi3-mmc drive: 0x/0x caddy
[ 7.570280] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 7.570356] sr 4:0:0:0: Attached scsi generic sg2 type 5
[ 21.312925] udev: starting version 151
[ 21.361174] lp: driver loaded but no devices found
[ 21.374163] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/LNXVIDEO:00/input/input6
[ 21.374330] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
[ 21.431538] Adding 3229024k swap on /dev/sda5. Priority:-1 extents:1 across:3229024k
[ 21.767984] nvidia: module license 'NVIDIA' taints kernel.
[ 21.767988] Disabling lock debugging due to kernel taint
[ 21.870264] type=1505 audit(1282865873.286:2): operation="profile_load" pid=601 name="/sbin/dhclient3"
[ 21.870613] type=1505 audit(1282865873.286:3): operation="profile_load" pid=601 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 21.870812] type=1505 audit(1282865873.286:4): operation="profile_load" pid=601 name="/usr/lib/connman/scripts/dhclient-script"
[ 22.323090] EDAC MC: Ver: 2.1.0 Aug 19 2010
[ 22.325257] i2c i2c-0: nForce2 SMBus adapter at 0x5000
[ 22.325293] i2c i2c-1: nForce2 SMBus adapter at 0x6000
[ 22.328941] EDAC amd64_edac: Ver: 3.2.0 Aug 19 2010
[ 22.340987] EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
[ 22.340999] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 22.341001] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 22.341003] (Note that use of the override may cause unknown side effects.)
[ 22.341031] amd64_edac: probe of 0000:00:18.2 failed with error -22
[ 22.446507] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[ 22.456314] cfg80211: Calling CRDA to update world regulatory domain
[ 22.477692] sdhci: Secure Digital Host Controller Interface driver
[ 22.477697] sdhci: Copyright(c) Pierre Ossman
[ 22.509278] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 22.524587] sdhci-pci 0000:03:05.2: SDHCI controller found [1217:7120] (rev 1)
[ 22.524612] sdhci-pci 0000:03:05.2: PCI INT A -> Link[LNKB] -> GSI 19 (level, low) -> IRQ 19
[ 22.524649] mmc0: Unknown controller version (16). You may experience problems.
[ 22.524906] Registered led device: mmc0::
[ 22.525043] mmc0: SDHCI controller on PCI [0000:03:05.2] using PIO
[ 22.526462] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 22.526470] HDA Intel 0000:00:10.1: PCI INT B -> Link[LAZA] -> GSI 23 (level, low) -> IRQ 23
[ 22.526475] hda_intel: Disable MSI for Nvidia chipset
[ 22.526512] HDA Intel 0000:00:10.1: setting latency timer to 64
[ 22.563159] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 22.564628] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 22.564634] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 22.564637] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 22.603487] cfg80211: World regulatory domain updated:
[ 22.603493] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 22.603497] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.603501] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 22.603504] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 22.603507] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.603511] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 22.606127] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 22.641159] sr1: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00
[ 22.641877] sr: Sense Key : Hardware Error [current]
[ 22.641882] sr: Add. Sense: No additional sense information
[ 22.822662] phy0: Selected rate control algorithm 'minstrel'
[ 22.824068] Registered led device: rt73usb-phy0::radio
[ 22.824169] Registered led device: rt73usb-phy0::assoc
[ 22.824271] Registered led device: rt73usb-phy0::quality
[ 22.825444] usbcore: registered new interface driver rt73usb
[ 23.164277] Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0
[ 23.201912] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[ 23.284872] EXT4-fs (sda7): mounted filesystem with ordered data mode
[ 24.760096] hda_codec: ALC262: BIOS auto-probing.
[ 25.260187] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
[ 25.654920] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 25.748203] type=1505 audit(1282865877.163:5): operation="profile_load" pid=950 name="/usr/share/gdm/guest-session/Xsession"
[ 25.753461] type=1505 audit(1282865877.173:6): operation="profile_replace" pid=952 name="/sbin/dhclient3"
[ 25.753830] type=1505 audit(1282865877.173:7): operation="profile_replace" pid=952 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 25.754034] type=1505 audit(1282865877.173:8): operation="profile_replace" pid=952 name="/usr/lib/connman/scripts/dhclient-script"
[ 25.758830] type=1505 audit(1282865877.173:9): operation="profile_load" pid=953 name="/usr/bin/evince"
[ 25.763986] type=1505 audit(1282865877.183:10): operation="profile_load" pid=953 name="/usr/bin/evince-previewer"
[ 25.766935] type=1505 audit(1282865877.183:11): operation="profile_load" pid=953 name="/usr/bin/evince-thumbnailer"
[ 25.794250] ACPI: PCI Interrupt Link [LNEC] enabled at IRQ 18
[ 25.794258] alloc irq_desc for 18 on node 0
[ 25.794261] alloc kstat_irqs on node 0
[ 25.794276] nvidia 0000:00:05.0: PCI INT A -> Link[LNEC] -> GSI 18 (level, low) -> IRQ 18
[ 25.794285] nvidia 0000:00:05.0: setting latency timer to 64
[ 25.794290] vgaarb: device changed decodes: PCI:0000:00:05.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 25.794562] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 195.36.24 Thu Apr 22 19:10:14 PDT 2010
[ 25.983335] rt73usb 1-6:1.0: firmware: requesting rt73.bin
[ 26.171813] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 26.270994] eth0: no link during initialization.
[ 26.271716] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.462806] /dev/vmmon[1179]: Module vmmon: registered with major=10 minor=165
[ 26.462827] /dev/vmmon[1179]: Initial HV check: anyNotCapable=0 anyUnlocked=1 anyEnabled=1 anyDisabled=0
[ 26.462834] /dev/vmmon[1179]: HV check: anyNotCapable=0 anyUnlocked=1 anyEnabled=1 anyDisabled=0
[ 26.462838] /dev/vmmon[1179]: Module vmmon: initialized
[ 26.479537] /dev/vmci[1187]: VMCI: Driver initialized.
[ 26.480549] /dev/vmci[1187]: Module vmci: registered with major=10 minor=55
[ 26.480555] /dev/vmci[1187]: Module vmci: initialized
[ 26.620005] ppdev: user-space parallel port driver
[ 26.650290] /dev/vmnet: open called by PID 1250 (vmnet-bridge)
[ 26.650301] /dev/vmnet: hub 0 does not exist, allocating memory.
[ 26.650331] /dev/vmnet: port on hub 0 successfully opened
[ 26.650352] bridge-eth0: up
[ 26.650357] bridge-eth0: attached
[ 28.528386] /dev/vmnet: open called by PID 1257 (vmnet-dhcpd)
[ 28.528400] /dev/vmnet: hub 1 does not exist, allocating memory.
[ 28.528432] /dev/vmnet: port on hub 1 successfully opened
[ 28.531997] /dev/vmnet: open called by PID 1259 (vmnet-netifup)
[ 28.532018] /dev/vmnet: port on hub 1 successfully opened
[ 28.533097] bridge-eth0: disabling the bridge
[ 28.560234] bridge-eth0: down
[ 28.560244] bridge-eth0: detached
[ 28.586524] /dev/vmnet: open called by PID 1262 (vmnet-dhcpd)
[ 28.586539] /dev/vmnet: hub 8 does not exist, allocating memory.
[ 28.586572] /dev/vmnet: port on hub 8 successfully opened
[ 28.593231] /dev/vmnet: open called by PID 1267 (vmnet-natd)
[ 28.593253] /dev/vmnet: port on hub 8 successfully opened
[ 28.596634] /dev/vmnet: open called by PID 1268 (vmnet-netifup)
[ 28.596657] /dev/vmnet: port on hub 8 successfully opened
[ 38.830086] vmnet8: no IPv6 routers present
[ 38.980092] vmnet1: no IPv6 routers present

bila lsusb
Bus 002 Device 002: ID 05c6:1000 Qualcomm, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0db0:6877 Micro Star International RT2573
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

sedangakan bila diakses dengan vmware, geemobile dapat berubah menjadi modem dengan dmesg berikut:
[ 1141.700139] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1141.927740] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1141.937123] usb-storage: device found at 2
[ 1141.937132] usb-storage: waiting for device to settle before scanning
[ 1142.170117] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1142.696996] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1142.697195] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1143.612871] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1143.837731] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1143.855702] usb-storage: device found at 2
[ 1143.855711] usb-storage: waiting for device to settle before scanning
[ 1144.080145] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1144.359883] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1144.580159] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1144.807763] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1144.814600] usb-storage: device found at 2
[ 1144.814613] usb-storage: waiting for device to settle before scanning
[ 1145.052565] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1145.338048] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1145.550546] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1145.777887] scsi8 : SCSI emulation for USB Mass Storage devices
[ 1145.791890] usb-storage: device found at 2
[ 1145.791906] usb-storage: waiting for device to settle before scanning
[ 1146.060218] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1146.362956] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1146.590192] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1146.817698] scsi9 : SCSI emulation for USB Mass Storage devices
[ 1146.831863] usb-storage: device found at 2
[ 1146.831877] usb-storage: waiting for device to settle before scanning
[ 1147.040144] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1147.311220] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1147.552642] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1147.777708] scsi10 : SCSI emulation for USB Mass Storage devices
[ 1147.780915] usb-storage: device found at 2
[ 1147.780924] usb-storage: waiting for device to settle before scanning
[ 1147.990169] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1148.262256] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1148.460163] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1148.687648] scsi11 : SCSI emulation for USB Mass Storage devices
[ 1148.695981] usb-storage: device found at 2
[ 1148.695991] usb-storage: waiting for device to settle before scanning
[ 1149.012610] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1149.295607] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1149.500134] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1149.727700] scsi12 : SCSI emulation for USB Mass Storage devices
[ 1149.744271] usb-storage: device found at 2
[ 1149.744281] usb-storage: waiting for device to settle before scanning
[ 1149.950132] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1150.230259] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1150.430141] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1150.657680] scsi13 : SCSI emulation for USB Mass Storage devices
[ 1150.668423] usb-storage: device found at 2
[ 1150.668433] usb-storage: waiting for device to settle before scanning
[ 1150.890135] usb 2-2: reset full speed USB device using ohci_hcd and address 2
[ 1151.164370] usb 2-2: usbfs: interface 0 claimed by usb-storage while 'vmware-vmx' sets config #1
[ 1152.303449] usb 2-2: USB disconnect, address 2
[ 1155.330139] usb 2-2: new full speed USB device using ohci_hcd and address 3
[ 1155.557507] usb 2-2: configuration #1 chosen from 1 choice
[ 1156.770171] usb 2-2: reset full speed USB device using ohci_hcd and address 3
[ 1157.210108] usb 2-2: reset full speed USB device using ohci_hcd and address 3

boleh minta bantuan solusi?

NB: di vmware aplikasi coneksinya keluar tulisan device disconnected
User avatar
aptfast
Posts: 3847
Joined: 03 Jan 2010, 23:38
Location: Jakarta, Indonesia
Contact:

Re: [Tanya] Instalasi modem geemobile

Postby aptfast » 28 Aug 2010, 23:57

ubuntu nya versi apa neh bro?

Return to “Solusi Hardware Ubuntu”

Who is online

Users browsing this forum: No registered users and 5 guests